dbuss

Main Level Bathroom Ceiling L Fade Start 1 Sat 2016/07/09 11:29:15 PM Web Log Scene:Smoke Alarm Fade Start 1 Sat 2016/07/09 11:29:30 PM Web Log Scene:Smoke Alarm Fade Stop Sat 2016/07/09 11:29:32 PM Web Log

Stu, The Zwave devices are controlled with a program. My error for not adding that bit of important.information.

I have a scene that is activated by a smoke bridge when a smoke alarm or CO2 alarm is activated. Last night the scene was activated. However it was activated with a fade start. There is no fade start in the scene. The scene has the lights turning on at 100%. Also, the Zwave devices in the scene were not activated. Just before the smoke bridge scene was activated the main level bathroom ceiling light was fade started. This light is controlled by a scene that is activated by a motion sensor. At this time of day the scene has the light turning at 35%. There is no record of the motion sensor being activated. We were not home at the time it happened, so I can't tell you if a smoke alarm went off. It appears it was started and stopped via the web. Could the fade starts and stops have been accidentally started when using Mobilinc? Thanks!!

I have a 2gig CT100 Z-Wave Thermostat and a RCS TZ45 Thermostat. The 2gig is being used where there was not a common 'C" wire. Both thermostats have been installed for about a year and have worked flawlessly. The battery has not needed replacement in the 2gig thermostat yet.

Thank you.

I figured it was something like this but had no idea what to do. I appreciate your help. Thank you.

I'm using an Elk motion sensor to turn on a stairs light when it senses motion. Which it does just fine. Then I want the light to turn off in 10 minutes. I can't get the light to turn off. I have two light switches(one at the top of the stairs and one at the bottom of the stairs) that are linked in a scene called Stairs Light. I've tried using motion to turn on the scene and that works fine. I've tried turning off the scene after 10 minutes and the scene will not turn off. Below is the program I'm currently using. Stairs Light On Night If From 9:00:00PM To Sunrise (next day) And Elk Zone 'Upstairs MS' is Violated Then In Scene 'Stairs Light' Set 'Stairs Light - Top of Stairs' 35% (On Level) Wait 10 minutes Set Scene 'Stairs Light' Off Else - No Actions - (To add one, press 'Action')

If you have Fire Stick with remote and running OS 5.0.3 or a Fire TV second edition with remote they have Alexa capabilities.

Teken, I had it happen to me for the first time this morning. I tried connecting to the same station again after the disconnection and it disconnected again. I changed stations on iHeart and it was fine on that station. I listened to it for a couple hours with no problems.

I've not experienced the problem on iHeart and listen to it quite often for pretty long periods of time.

I have four Schlage door locks, three Linear garage door controllers, two Z-Wave thermostats and two Aeotec range extenders. Our home is about 5000 sq. ft on three levels including garage space. The house is 78 feet long with lower level garages on both ends. My ISY is on the lower level pretty close to the center of the house. All devices work fine.

The tilt sensor works fine. You see the status of the door...open or closed.It does not act as secure repeater. I like the feature that it sounds an alarm before the door moves when you use the Linear controller to open or close the door. I'm sure the Aeon device will a good product too once it becomes available. I've been happy with the Aeon products I have.

I have three Linear GD00Z-2 garage door controllers. They work very well.

I like the ability to use Echo to turn lights on and off as do many others it appears by the various posts in the forums. We have two Echos and a Fire TV in our house that we use with the same ISY.

The first thing you should do is get your Ui the same version as your firmware.

Yes, I have two Z-wave thermostats on the same ISY controlling two different furnaces and air conditioners.

I have a 2gig CT100 Z-Wave thermostat and an RCS TZ45 Z-Wave thermostat. Both have worked well.

This is impressive!! I live in WI and presently on a business trip on Long Island. The setup was completed with my phone here on Long Island. I called my wife and had her try it out and it worked flawlessly. Congratulations on a job well done. Sent from my XT1254 using Tapatalk

Stu, Have you tried "Alexa, ask Izzy to turn off dining room" or replace "turn" with "switch"?

You could also try changing the one word description. "Kitchen" does work on my Echo. Sent from my XT1254 using Tapatalk

Are you saying, "Alexa, tell Izzy to turn on kitchen? Sent from my XT1254 using Tapatalk

If you use one word names for your devices, you will have much better results. Sent from my XT1254 using Tapatalk

Hi Michel, I'm connecting locally.

My admin console is very slow to update the status of the devices today. I can send commands through the admin console and they are executed as normal. However, it takes quite some time for the status of the device(s) in that command to update. The devices seem to update as usual when I access my ISY through the UDI Portal. Also when I sign out of the admin console it takes awhile for me to be able to sign back in because the admin console thinks I'm still signed in. This does not happen when I connect through the UDI Portal. Echo is also performing as normal. I am also unable to get the status of my devices on Mobilinc today.

If you had the UDI portal you could also install MobiLinc on a tablet and that would give your guests control of the devices without the ability to change programs, scenes, etc. in your ISY.