dbuss

I have a ceiling fan controlled with a Fanlinc and two 6 button KPLs that I'm trying to get to work with Alexa. The only command that works with Alexa is the off command. Alexa recognizes the other commands, however the fan doesn't turn on or change speeds. The fan is controlled as expected from the KPLs. Here are screenshots of the admin console showing the four scenes and showing how I have Alexa configured in the portal. What am I missing? Thank you!

Try restarting the node server.

Thank you @MrBill. I needed to tweak it a bit more, but you got me on the righ track Here's what works: ${sys.node.n004_78633.CLITEMP}

I want to include the Temperature in the attached image in email notifications. When on PG2 this worked in my email notifications:${sys.node.n004_temperature.ST} Since going to PG3 it does not work. What do I need to change to make it work? Thank you!

It appears that your Wireless Tag node server has not found your wireless tags manager. Make sure you have the correct "oauth2_code" entered in the node server Custom Configuration Parameter.

Have you clicked on "Discover" in your Wireless Tags Controller in the Admin Console? Are your tags showing up in the node server nodes?

Have you tried restarting the node server?

Your updated PG3 node server works great! Thank you!

PG3 Purple Air is working fine here.

Once you have followed the instructions above for updating your Polisy, the next step is to SSH ISY on your Polisy. Without IoP installed, there is nothing for the ISY Launcher to find.

I found that using a Mini Remote to turn the Lamplincs on and off and place the Mini Remote near the lamp works well for me.

This is true as long as the device is within the Z-Wave RF signal. Your symptoms indicate that you need more repeater devices to create a larger and stronger mesh network so the Z-Wave signal can reach all of your devices.

If all the devices are not in the same location, you might try moving the two that don't work, closer to your ISY tp see if it might be a communications problem.

When you click Z-Wave you will see this drop down menu. Click on "Remove a Z-Wave Device" Then you will see this. Follow the instructions that came with your device to remove your device from your Z-Wave network.

Extenders do need to be added. Try excluding the device and then try adding it.

I had this same situation recently and the flash chip was corrupted. Here's a link to the wiki that describes the situation and what you need to do to correct the problem. UDI sent me a flash chip. https://wiki.universal-devices.com/index.php?title=Polisy:User_Guide#The_Third_Light_Is_Constantly_On_While_Everything_Else_Is_Off

Thank you @Michel Kohanim for helping me solve this problem. The TPM board was not seated properly which started causing more issues. Once the TPM board was seated properly all worked as expected. I expect the TPM board issue was the result of me not being careful when I opened and closed the cover on my Polisy.

Did you make sure zwave did not become unchecked? Yes. I also unchecked it and saved it and then rebooted. Then checked it again. Saved it and rebooted. Are you getting an error message? It says Z-Wave dongle not responding.

I reinstalled Simplicity Studio and seemed to get the Zooz stick updated. Apparently had didn't have something installed that I should have. However, now IoP doesn't recognize the Zooz.

Here is a screen-shot of where I am. I can't seem to figure out what I need to do next. Thank you!

I don't know if it's the "best". I use iBlinds for our horizontal blinds and they work well for me. https://myiblinds.com/

This the correct Richmond Capital Partners. https://opencorporates.com/companies/us_wa/604051836

If both the MEM and ERR LEDs are blinking, the ISY is unable to communicate with your Ethernet network.

I'm not surprised considering it's a holiday weekend. Although Insteon is important to us users, in the grand scheme of things in the tech world, I question if it's big enough to garner a lot of attention.