dbuss

Thank you for the explanation!

@JaviIf a program A turns a device on, will program B see it as the device being switched on or would program B be looking for a change in the device status?

I programmed a notification using "Control" and then re-programmed it using "Status" and both worked fine.

Have you tried using "Status"? If not, try it and see how it works.

I've Found that "Control" works much better with Insteon switches.

Is your switch an Insteon or Z-wave? I've found that when using "Control" with some Z-Wave devices, my Eisy doesn't catch the control action quick enough to trigger the program. Using status seems to have helped that.

The Aeotec Motion Sensor M6001-MTP is attempting to connect when it's flashing red and green. If you use UD Mobile you may want to try and connect it by using the QR code on the device.

It is normal. However, you should not display this information publicly. Block out the uuid information so it can't be seen.

I've added a Zooz Zen 16 to my Eisy. The Zen 16 added and the power node and the three switch nodes. However, there is no information in the switch nodes. The power node is working as it should. I can turn the Zen 16 power on and off from the admin console. I can hear the Zen 16 switching when it's triggered. But the information does not get to the admin console. I've used the update with interview several times and I've removed the Zen 16 and readded. Has anyone successfully added the Zen 16 to an Eisy? Thank you! Problem solved. I had to include it with no security. Works great now.

I've attached a screenshot of the configuration panel in my Push Plug-in. Here's an example of how I use them in a program. Garage Door Open Notification - [ID 0003][Parent 0001] If 'ZY 213 Garage Door' Status is Open Then Set 'Polyglot / Push / Garage Door' Message Open Else - No Actions - (To add one, press 'Action')

I experienced similar issues with one of my locks. I tried three different locks and all had issues. The fix for me was to find a location for the Eisy that it could communicate reliably with my two door locks. Since then my lock issues have disappeared.

I appreciate this information. Thank you! I got the 2nd generation alarms to add and display correctly by putting them right next to the Eisy when adding them. The 1st generations would not add.

if you delete them, they will most likely return. Most have a file named unused nodes and put them all in there. That way they are out of site...out of mind.

I've had success doing this with other Z-Wave devices but no success with the First Alerts. I will continue with this approach. Thank you!

For what it's worth. I've experience this with a few Z-Wave devices and currently with my First Alert ZCOMBO alarms. The other devices that experienced this I was able to get all the nodes by removing and re-adding and in some cases preforming several interviews. Thus far I've been unsuccessful doing this with my First Alert alarms.

I've had the 994, Polisy, and now Eisy and couldn't be happier. I had struggles with the Eisy in the beginning. But now it's working great. I installed my daughter's Eisy this past weekend and I'll be installing my son's this week. Eisy is a great product for me.

Thank you @RPerrault. These are the nodes I used to have also. I need to figure out why I no longer have them.

Only one of the outlets on this receptacle is Z-Wave controlled. The other is a pass-through outlet.

The images below are screenshots of my AC for a First Alert ZCOMBO device. If you are using these alarms are these what you are seeing in your AC device tree and programming screen when trying to use the alarm in a program? Thank you!

Do You have Z-Wave support turned on?

I've used the "Remove Failed Node" and the deleted the device. These options are available when you right click on the device in the admin console.

I appreciate this information. I've been using a Z-Wave controlled WaterCop and it has worked well for me. However, WaterCop stopped producing them so, I know at some point, I will need to replace it with something else.

The dropdown menu should show the values as in the image below.

@DennisC I think I've solved the problem, thanks to the questions you asked. I already had a program to turn the garage lights on if the garage entry door was unlocked. I added a wait time and then turned off the garage lights and locked the garage entry door. I already have a program that if the light switch is turned on manually, the programs are disabled for an hour for those instances when I want to be in the garage longer than the wait time in the program.. Thank you fro the assistance!

Hi Dennis, I thought it had to be something with the trigger and appreciate your help. Here is what I would like to accomplish. 1. If I open the garage door, I would like the program to turn the garage lights off and lock the garage entry door two minutes after the garage door closes. 2. If the garage entry door is unlocked, I would like the the garage lights turned off and the garage entry door locked two minutes after the garage entry door in unlocked. I may change the wait times. Thnak you!