bgrubb1

Michel This is so cool, thank you for letting us "play" ...Barry

i had a similar issue after switching serial PLM to USB A sudo service isy restart with USB plugged in fixed it It appears it's USB but not plug and play Needs PLM installed when ISY starts ...Barry

I re-capped one and plugged the serial daughter board in wrong. Pretty sure I blew the daughter board. Please PM me ...Barry

All good here as well Thank you Michel

Hmmm No Joy here. still get [admin@polisy ~]$ sudo service isy restart isy not running? (check /var/isy/isy_daemon.pid). loading uftdi.ko kldload: can't load uftdi.ko: No such file or directory /usr/local/etc/rc.d/isy: WARNING: failed precmd routine for isy [admin@polisy ~]$ ....Barry

same exact result here

same here Seen in AC, but constant spinning with no connection

entire row shifted only 4 of 8 connected whole row connected to incorrect row

Sooo rookie mistake I took a perfectly working 2413S and re-capped it as a preventative measure When I put it back together i had the serial board only plugged in on one row of the header. Plugged it in to a red light instead of green. Corrected the issue and have a bright green light but no communication. Suspect I blew the serial interface. Does that sound reasonable ?? does anyone have a dead 2413 S that might have a good serial board they might sell ?? ...Barry

@Michel Kohanim I rebooted the Polisy then plugged in the USB PLM (after fully booted) now I get ugen0.2: <FTDI FT232R USB UART> at usbus0 ugen0.2: <FTDI FT232R USB UART> at usbus0 (disconnected) ugen0.2: <FTDI FT232R USB UART> at usbus0 ugen0.2: <FTDI FT232R USB UART> at usbus0 (disconnected) ugen0.2: <FTDI FT232R USB UART> at usbus0 Now the AC is in a loop and displaying

igb2: netmap queues/slots: TX 4/1024, RX 4/1024 pci0: <encrypt/decrypt> at device 8.0 (no driver attached) xhci0: <AMD FCH USB 3.0 controller> mem 0xf7fa2000-0xf7fa3fff irq 18 at device 16.0 on pci0 xhci0: 32 bytes context size, 64-bit DMA usbus0 on xhci0 usbus0: 5.0Gbps Super Speed USB v3.0 ahci0: <AMD Hudson-2 AHCI SATA controller> port 0x4010-0x4017,0x4020-0x4023,0x4018-0x401f,0x4024-0x4027,0x4000-0x400f mem 0xf7fa5000-0xf7fa53ff at device 17.0 on pci0 ahci0: AHCI v1.30 with 2 6Gbps ports, Port Multiplier supported with FBS ahcich0: <AHCI channel> at channel 0 on ahci0 ahcich1: <AHCI channel> at channel 1 on ahci0 ehci0: <AMD FCH USB 2.0 controller> mem 0xf7fa6000-0xf7fa60ff irq 18 at device 19.0 on pci0 usbus1: EHCI version 1.0 usbus1 on ehci0 usbus1: 480Mbps High Speed USB v2.0 intsmb0: <AMD FCH SMBus Controller> at device 20.0 on pci0 smbus0: <System Management Bus> on intsmb0 smb0: <SMBus generic I/O> on smbus0 isab0: <PCI-ISA bridge> at device 20.3 on pci0 isa0: <ISA bus> on isab0 sdhci_pci0: <Generic SD HCI> mem 0xf7fa7000-0xf7fa70ff at device 20.7 on pci0 sdhci_pci0: 1 slot(s) allocated amdtemp0: <AMD CPU On-Die Thermal Sensors> on hostb5 uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0 uart1: console (115200,n,8,1) tpm0: <Trusted Platform Module> port 0xc31-0xc32 iomem 0xfed40000-0xfed44fff on acpi0 tpm: device 0x001a15d1 rev 0x10 WARNING: Device "tpm" is Giant locked and may be deleted before FreeBSD 14.0. orm0: <ISA Option ROM> at iomem 0xee800-0xeffff pnpid ORM0000 on isa0 superio0: <Nuvoton NCT5104D/NCT6102D/NCT6106D (rev. B+)> at port 0x2e-0x2f on isa0 gpio0: <Nuvoton GPIO controller> at GPIO ldn 0x07 on superio0 gpiobus0: <GPIO bus> on gpio0 gpioc0: <GPIO controller> on gpio0 hwpstate0: <Cool`n'Quiet 2.0> on cpu0 Timecounters tick every 1.000 msec ZFS filesystem version: 5 ZFS storage pool version: features support (5000) Trying to mount root from zfs:zudi/ROOT/default []... Root mount waiting for:ugen1.1: <AMD EHCI root HUB> at usbus1 ugen0.1: <0x1022 XHCI root HUB> at usbus0 usbus0 CAM usbus1 uhub0 on usbus1 uhub0: <AMD EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 uhub1 on usbus0 uhub1: <0x1022 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0 uhub1: 4 ports with 4 removable, self powered ada0 at ahcich0 bus 0 scbus0 target 0 lun 0 ada0: <SATA SSD SBFM61.3> ACS-4 ATA SATA 3.x device ada0: Serial Number 218807050F8D00029175 ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes) ada0: Command Queueing enabled ada0: 30533MB (62533296 512 byte sectors) Root mount waiting for: usbus1 uhub0: 2 ports with 2 removable, self powered ugen1.2: <vendor 0x0438 product 0x7900> at usbus1 uhub2 on uhub0 uhub2: <vendor 0x0438 product 0x7900, class 9/0, rev 2.00/0.18, addr 2> on usbus1 Root mount waiting for: usbus1 uhub2: 4 ports with 4 removable, self powered Root mount waiting for: usbus1 ugen1.3: <vendor 0x0cf3 product 0xe003> at usbus1 Dual Console: Serial Primary, Video Secondary apuled0: <APU2> at iomem 0xfed81610-0xfed8161b,0xfed81664-0xfed81667 on isa0 resetsw0: <UDXRSW-2> at iomem 0xfed81664-0xfed81667 on isa0 lo0: link state changed to UP igb0: link state changed to UP ubt0 on uhub2 ubt0: <vendor 0x0cf3 product 0xe003, class 224/1, rev 1.10/0.01, addr 3> on usbus1 WARNING: attempt to domain_add(bluetooth) after domainfinalize() WARNING: attempt to domain_add(netgraph) after domainfinalize() Security policy loaded: MAC/ntpd (mac_ntpd)

Still trying to get USB to work. I Installed the FTDI drivers and PC sees the USB interface. Anything else I can try ? ..Barry

interesting question.... I initially hooked up a USB PLM (it was old but working last time I knew, way back in the Vera days) it said not connected although it responded to the reset button. I re-capped it today and it still appears functional, but not seen by ISY ...Barry

Similar issue here in AZ Polisy set to Phx (no DST) ISY reports LA ...Barry

@Michel Kohanim anything I can try to get around the ISY automatically discovered at http://192.168.0.27:80 however the username and password need to be set in the settings menu. I can access the ISY on Policy via ISYFinder Once I try to set the ISY password on Polisy the ISY still runs but doesnt respond to commands and Polisy URL will not connect until I restart the ISY ...Barry

@Michel Kohanim if you mean can I login to the ISY on Polisy via the ISY Finder - Yes I have added a couple of Insteon devices and wrote a few programs. Works fine until I try to set the ISY password in Polyglot on the Polisy After pressing save the ISY is still responsive in the UI but devices do not respond until I restart the ISY ...Barry

Done but.... I am still getting the ISY automatically discovered at http://192.168.1.145:8080 however the username and password need to be set in the settings menu. Any workaround for this ? ...Barry

I have the same "password of ISY needs to be set" issue If I try to set it I can no longer access Polyglot and the ISY becomes un-responsive Restarting ISY brings me back to the password loop ...Barry

Michel I bought a "Dev" Polisy Pro to start testing. Is the USB PLM working now ? ...Barry

Did something change with subscriptions from this maintenance ?? If I try to get to any of my managed ISY's via the portal using the Admin console, the initialization hangs at "Starting Subscription" ...Barry

in addition when amps are turned up too high they tend to "clip" aka not produce a clean signal wave which has a high DC component for a signal not intended to be DC

Thank you

secret might be making the Alexa category Light instead of scene

should I said I don't have a 4th gen but have gen 1 through 3 devices and they all work fine

hmmmm I have a scene called kitchen lights that combines two switches on two separate circuits that I went through this with a while ago. Just walked into the kitchen and confirmed it works for me.