asbril

I am not sufficiently knowledgeable to know whether this is an Inovelli or ISY issue, but it is defnitely a complication that Inovelli inclusion/exclusion method is very different from the major brands.

Larryllix, probably your hacienda is too large for GH........?

I use pre-fixes such as "master fan" ; "office fan", etc and this works for me.

Why not simply call then "beer lights" ?

Thanks Whitehambone I will check

5012 UPNP SUBSCRIBER NOREPLY TO EVENT 1 subscriber didn't reply to the event:couldn't write header Thanks, but unfortunately it does not tell me which device or program is the cause.

Sun 2020/05/17 04:16:42 PM System -5012 50 What is the meaning of this error message ?

I don't think there is any control of Zwave sensors in ISY, other than disable/enable. I believe that one can change the parameters, such as duration of sensor's ON but I have not played with that yet.

You are right..... I use Zwave sensors and I can not turn OFF these sensors from the AC. I thought indeed of adding a time factor, but have to think about this more.

Thanks Larryllix, at first look maybe a bit too complex for me but I will look at it.

Thanks, I have resolved my issue with 3 programs : (1) IF Motion Sensor is ON THEN Light X goes ON Wait 2 minutes Light X goes OFF (2) IF Light X is switched ON THEN Stop Program (1) Disable Program (1) (3) IF Light X is switched OFF THEN Enable Program (1)

Indeed, in fact I created programs so that my Administrative Console shows 33-67-100, even when I set a different percentage or voice command. This is not really necessary but better reflects status.

My 4 fans (from Home Depot) work with these switches, and work fine with both Alexa and GH, using "Fan" in Portal-Connectivity-Alexa / Google Home. The default speeds are Low= 33 %; Medium=67%; High and Max = 100%

https://smile.amazon.com/GE-Enbrighten-Required-SmartThings-14287/dp/B06XTKQTTV/ref=sr_1_2?crid=KO3750X4W487&dchild=1&keywords=zwave+fan+control&qid=1589585051&sprefix=zwave+fa%2Caps%2C182&sr=8-2

I guess that on question what fan we use, the Zwave fan includes a regular fan with a. Zwave fan switch.....

That depends on how many Zwave devices you have between your bathroom and your ISY. Zwave is a mesh network and the more (non-battery) devices you have the better the communications. Teken suggested that you get repeaters, but I always suggest to get a few plug-in devices, as these are both repeaters AND you can connect a lamp (or any device) so that you actually have a use of the repeating device. Depending on the distance between the bathroom and ISY, 1,2 or 3 repeating devices should be sufficient. Also remember to perform a Zwave "heal" after you add Zwave devices to your network, as this helps optimization of your mesh network.

Eric's lack of support says it all.... I now only use Homeseer and GE/Jasco switches

IF light X is switched on THEN stop program 1 Disable program 1 Or else Enable program 1

I had the Enable in Else of Program 2 I also believe that keeping Status of Ceiling is ON on top of Switch is an issue. Now I have the following : Program 1 IF Motion Sensor is ON THEN Light X is ON wait 2 minutes Light X OFF Program 2 IF Light X is switched ON THEN Stop Program 1 Disable Program 1 Program 3 If Light X is switched OFF or Status Light X is OFF THEN Enable Program 1 I believe that if I keep in Program 1. IF Light X is switched ON or Status Light X is ON then in Program 1 Light X will not go off after 2 minutes, because Program 2 stopped and disabled Program 1 This works in simulation in Administrative Console, but I still have to check when Motion sensor is activated. Let me know if my logic makes sense.

My experience is that the enable in ELSE did not work, so I created another program : IF Laundry Ceiling Light is Switched OFF or Status Laundry Ceiling Light is OFF THEN Enable program This seems to work when I simulate from my Administrative Console, but still have to try with the motion sensor in action, but it should work. Thanks for your guidance.

Many thanks lilyoyo1, The only part I don't understand is And (Light is not switched off or status ceiling light is off)

This looks similar to my alternative, which I will try now.

Benoit ci-joint la video The video is a bit shaking but it shows my steps. IMG_3469.MOV

I had already used Chrome on both my Windows 10 and on my Mac. Same result. Just now I tried on Windows 10 with Edge browser and same result.

In our laundry room we have a door to the outside and I have a motion sensor that is programmed to turn the ceiling light ON upon motion. However whenever someone is the laundry room for a longer time than just passing through, the light, after the set period of 2 1/2 minutes, goes OFF and then goes ON straight away. This is a bit annoying. What I want is that when someone has already turned ON the Laundry Ceiling light, then the motion sensor does not turn On the light. I designed 2 programs : Program 1 IF : -empty- THEN : set laundry ceiling ON wait 2 minutes and 30 seconds set laundry ceiling OFF ELSE : -empty- Program 2 IF : ceiling light Status is OFF and Motion Sensor is ON THEN : Run program 1 But this does not seem to do the job. Would an alternative something like the following do the job ? Program 3 IF : Motion sensor is ON THEN : Laundry Ceiling Light ON Wait 2 minutes 30 seconds Laundry Ceiling Light OFF Program 4 IF : Laundry Ceiling light is switched ON THEN :Disable Program 3 Program 5 IF : Laundry Ceiling Light is switched OFF or Status Laundry Ceiling Light is OFF THEN : Enable Program 3 I look forward to any ideas and insight, Thanks