tibbar Posted December 13, 2015 Posted December 13, 2015 Hi! I have 3 Yale locks YRD220-ZW, everything seams to work well.I just bought a new lock YRD120-ZW. This is a new model with integrated Zwave chip oposed to old one YRD240-ZW which has plug-in Zwave module. When I try to open options page first it gives a SLL error (see image) and if i close and reopen options page just get an error. My ISY ver. is 4.3.26. Anything I can do to fix it?
fryfrog Posted December 14, 2015 Posted December 14, 2015 Once you get this sorted out, I'm curious to see how your battery life ends up. It'd be nice if they made some design changes that resulted in longer battery life. I've got 4 of the older ones and battery life was a handful of weeks if I was lucky, but after a tip here or from reddit, I added a status test so that I'd only send commands when they were needed and it doubled or tripled the battery life. For example, when the front door is locked I send a lock command to all the others... I changed that behavior by adding an "if not locked" test for each lock to cut down on the number of noop signals sent.
bob123 Posted December 15, 2015 Posted December 15, 2015 I have the same issue with the newer keyless (YRD120-ZW) yale locks. I have 2 of these. My other lock with key (YRD220-ZW) works just fine. I get the same error message as the OP when trying to access the options page. All other interactions with the locks seem fine, although one seems to randomly show status of unlocked when it has not been touched. Not sure if that is a zwave issue or not.
Michel Kohanim Posted December 16, 2015 Posted December 16, 2015 Hello all, We need to buy one of these and see what's going on. Can you please verify that all of you have 4.3.26 firmware and UI? With kind regards, Michel
bob123 Posted December 17, 2015 Posted December 17, 2015 Here are my versions ISY version 4.3.26 UI version 4.2.18
MWareman Posted December 17, 2015 Posted December 17, 2015 Here are my versions ISY version 4.3.26 UI version 4.2.18 Your UI should match the ISY version. You'll need to clear your Java cache.
LeeG Posted December 17, 2015 Posted December 17, 2015 bob123 Need to upgrade UI to 4.3.26. Go to first post for 4.3.26, use 4.a to upgrade UI. Be sure to clear Java cache
bob123 Posted December 18, 2015 Posted December 18, 2015 Upgraded the UI to 4.3.26. Same issue. Tested all 3 locks multiple times. Older lock works fine. The two newer keyless locks fail on the options page.
Michel Kohanim Posted December 18, 2015 Posted December 18, 2015 Hi bob123, I am so very sorry to hear. The lock is on order and we should get to it shortly. With kind regards, Michel
joelika Posted December 24, 2015 Posted December 24, 2015 For what it's worth, I get the same "request error", but I was pretty sure when I first set it up back in August of this year, I didn't. I think that was with an earlier version of the ISY UI and firmware, but I don't remember. I'm on 4.3.26 now for the firmware and UI. @fryfrog, I installed the lock the end of Aug 2015. The battery life is at 87% with the original batteries.
tpiacentine Posted December 27, 2015 Posted December 27, 2015 I have a Yale lock that was connected to my Veralite equipment and then I switched the ISY and added in the Z wave module. I am not able to add it to my network. Is there a way to find out why it will not add?
fryfrog Posted December 28, 2015 Posted December 28, 2015 Do an exclude or two first. Move it close to the ISY. Those are the two main things for getting a lock to pair, in my experience. Pairing before installation w/ it next to ISY has been my best result. Moving the ISY is painful because of network and PLM, but I've done that too.
Recommended Posts
Archived
This topic is now archived and is closed to further replies.