apostolakisl

I am trying to get elk to initiate an ISY program. The program is currently triggered by pushing a kpl button (not the load). The kpl button is in a scene as a responder and controller. The program triggers a bunch of network commands to my global cache. Elk is set to turn the scene off. The button backlight does turn off, but the program that is controlled by that button doesn't run. I tried setting the program to run as both control and status of the button. The program runs fine when I push the kpl manually. What am I missing here?

Devices should report and show the current state on ISY's main console regardless of how they got that way. You should not have to close your window and reopen it to have the state be shown accurately either. I can sit at my console and watch as my wife and kids move around the house turning lights on and off. I had a KPL that was not reporting state properly and found that a factory reset of the kpl follwed by a "restore device" fixed the issue. If nothing on your system is reporting state, I would think that perhaps you are having a plm issue. If the ISY is not getting the word when a device has its state changed, then programs triggered by those status' won't work either. Check to see if programs are functioning that are initiated that way. If reopening the Java console gets the state to show correctly, then you must be having a Java communication problem with ISY knowing what is going on, but it just isn't showing up on your screen. Try rebooting your computer or reinstalling Java.

Any idea on how to get volume keys to behave like volume keys? In other words if you want to get a held key to keep sending the command to the itach until you let go?

I have discovered some finer points to this. Some remotes require you to change some of those settings which earlier we glossed over. In programming my dish vip 622 I have discovered that I needed to change the "gaps" setting to 3. It appears to truncate the code to essentially nothing. If you hit the "trim" button and it pretty much cuts everything out, try increasing the gaps. If I figure out what the other settings do I will let you know. If anyone else can explain what all of these settings do, please feel free to write a nice little description here. Thanks!

I think that the way this works is that Elk addresses a device internally using the x10 type terminology which outputs an Intseon address via IP (not powerline), which the ISY accepts and transmits on the powerline. In short, I believe that the x10 type address is not going to affect anything outside of Elk, so I think that should work.

So after doing that, when Elk turns one of those devices on, it actually turns on, right? You never said that you actually tested it, but I just have to believe you did

I have been replacing a lot of my switches recently. Programs weren't working right so I started looking into it and discovered that several of the programs including switches I changed out didn't get the message. They said something to the order of "not specified" or something like that where it should have had the switch. Some did transfer, but others didn't.

Rebooting the computer seems to have fixed the problem. It now loads 2.8.4 as usual by simply entering the url in IE.

I have been playing with this itach and couldn't get it to work. I kept gettig errors. Then I tried appending with "\r\n" (not the ,\r,\l as listed above) as the gc 100 wiki says and that worked! I haven't a clue what any of this stuff means, why it is there, or anything. Just utterly clueless!

I can't figure out what else to delete to get Java to use the 2.8.4 version. I went through the Java control panel and looked under every tab and setting screen I could find and deleted everything I could find. I also tried acessing through touch switch admin button and I get the ISY console without 2876db support.

Yes, that was what I meant by "trying the URL you listed". It only works using this url. Using the regular method of just putting the local IP address gives me the same console but without full 2876db support. The following URL does work. http://www.universal-devices.com/99i/2.8.4/admin.jnlp I am just confused on how this is different than the other way of accessing the Java console. I did clear my Java temporary internet files and the first time I ran the console after clearing those files it did do the much longer load time with the little java loading clock showing presumably indicating that it was reloading all of the files. I can still load the java console the other way (my ip/admin) and even have both open at the same time. The my ip/admin continues to not have the 2876db support even open side by side with the .jnlp opened console.

OK, using the URL you listed works. I am confused, what is this new URL doing? It appears to be using Java very differently but brings up the identical appearing console.

Yes, I opened the Java from control panel and clicked on delete all temporary files. I log on by going to my local URL and it brings up the Java interface. http://192.168.1.9/admin I just did this on a different computer as well and the results continue to be unchanged.

I upgraded to 2.8.4. No change. When I switch the drop down programming "if" menu from "status" to "control", all of the new 2876db items vanish. Of note: I also replaced the icon relays (2876sb v.39). These do not have the problem. The show up in both "status" and "control" menu (new ones and old ones).

Here is one of the new 2876db's that doesn't work - 16 43 BC 1 Alexis BR/Overhead 30795 1.30.57.0 true G08 And here is one of the older 2876db switches which are supposedly the same thing but does work. - 3 6E 83 1 Game Room/Coach L 59423 1.3.38.0 false F05 <

- 30795 Alexis Room

Icon 2876db v.39 dimmer switches. In writing programs, you can not do the following: if control 'icon switch xyz' is switched on All of the 2876db switches simply do not exist in the drop down menu. They do exist for the status drop down menu. I still have a couple of the older 2876db's and they are on the drop down menu. Interestingly, the ISY calls them 2876d3's even though they are supposedly 2876db's.

I have just gotten sh to replace all of my icon switches that are previous to the fixed paddle issue. Anyway, I went to do some programs with the new switches and when I try to use the "control" set of parameters, the new icons all disappear. The icon switches that are of the older vintage are all there. What gives?

I did that exact same thing but used my Elk panel's relays instead of Insteon relays to control it. When I speak of "it" I mean my garage door openers, not a car starter. Maybe if you have a detached garage, but the risk of the car starting and pumpin CO into my house accidentally scares me.

I am confused by why the program is causing the light to turn on and off repeatedly. I do understand why it would fail to complete. As I see it, when the first light in the program has it's status addressed by the then section of the program, the program will retrigger (terminating the execution of the then/else parts) and thus not complete the turning on of the second light. This would get caught in a loop until it is no longer between sunset and 10:30 or until somehow both lights became on. Where is the command that is turning the light off? What am I missing here that would make the lights go on/off/on/off as I believe was what the original question was?

Scenes and Programs may effectively do the same things, but are not at all the same things as to how they go about doing it. Scenes are directly programmed into the Insteon switches, kpls, etc. These are the links that can be created manually (no ISY or other software/hardware required). The ISY can be used to automate the process of creating scenes and is a lifesaver for anything more than the simplest of scenes, but ISY is not required. Programs are written into the programming section of ISY. They are totally run by the ISY. The insteon devices can be told to do things by a program, but without ISY, programs don't exist. Programs offer a whole lot of options that scenes can not do. But, they are quite a bit slower than scenes. A scene will usually happen in a small fraction of a second (instantly as far as most applications are concerned), whereas a program that does the same thing may take a couple seconds. If you are trying to create a group of insteon devices to respond to another insteon devices in the same way everytime, use a scene. If you have more complex if/then parameters, you need to use a program. In this example, pushing the kpl button does something different with each press. Programs are therefore required. The "F" programs (flags) do nothing but get set to true or false. If the "F" program is executed from another program as either a run "then" or run "else" it will cause the status of that program to become true or false respectively. Other programs can then reference that true or false status as part of the if section. You can think of it as binary code. Using 2 flag programs is like 2 bit binary. 00, 01, 10, 11. So with those 2 flags you can have other programs respond in 4 different ways. I hope I got all of this correct. I encourage others to critique my explanation!

I would not use Insteon for this. I find the reliability to be too low. If there was a failure to shut off your heat or whatever it could cost a lot at those kind of electricity prices. Maybe the newer dual mode Insteon stuff that uses RF as well as power line code would be reliable enough. I use my Elk M1G for stuff like this. Soon (I hope) Elk will be fully integrated with ISY so you can use that programming interface. A simple and cheap hardwired relay will work on your water tank and there are a number of thermostats that will communicate with Elk. You will need a trigger for your system to know that you are about to show up. What that trigger is, only you can determine since only you know when you are going to be there. You can have Elk or ISY send you email or text notification of turning your vacation house on/off or other conditions as you see fit.

I have used my Elk m1 to prevent water damage by installing water sensors through the house. http://www.homesecuritystore.com/p-48-2 ... witch.aspx I have wired these to zones on my alarm panel and when the circuit closes because water touches the contact, the system alarms. Furthermore, I have an Elk whole house automatic valve. http://dpcdist.com/watershutoffvalve.aspx The Elk alarm panel closes a relay that closes the valve during a water alarm shutting down the whole house. In addition, I have it set to shut the house water off 45 minutes after the system is armed away. Using this device from insteon http://www.smarthome.com/2450/IOLinc-IN ... ut-/p.aspx you could monitor one water sensor and control one water valve using your ISY instead of an Elk. I paid less than the prices on those websites, those are just what came up when I googled my products for your reference. Once the status of the water sensor and valve are known to the ISY, you can do with that what you will. Send emails, sound sirens, flash lights, send text messages, you get the idea.

I haven't used an outlet linc, but wonder if it doesn't have a temp or current overload switch on it. Is the AC unit near (or over) the outlet linc amp rating? Such a device might very well be reset by a power cycle to the outlet linc. Have you tried calling smarthome and asking?

So you are saying that the buttons are still part of the other scenes, you just created a new scene that is the same as the other scene but with all buttons and switches as contollers, no responders?