JSchumann

Interesting idea! Thanks

I bought some used Motion sensors 2842-222 and it appears they were used outside and the stickers with the address are gone. I looked all over the device, took it apart and looked at the board with no luck. Is there a way to link them without knowing the address? I tried the new insteon device, and also the start linking icons. Thanks, John

Thanks, That is a different start guide than I have......

Oh cool, will try it. Where are the button sequences documented?

Got it. Thanks

Correct, I have it off I think. The box is blank......previously had ON.

Motion

Ok, so I moved the DIP setting to off. The dusk to Dawn notification is blank now (doesn't say Off). So it should work as a room sensor now. Thanks, John

Yes, UI Matches

Motion Sensor 2842-222 ISY 994i 5.3.0

In the Right screen for my motion sensor, Dusk to Dawn page, Status says ON. I cannot get it to turn off. This sensor is used in a room. Jumper Pin 3 is open, so it is NOT in night only mode Jumper pin 5 is closed, so I have Remote software enabled. In options I have sensing mode unchecked, on command only unchecked and night only mode unchecked I have written changes to device. Status for dusk to dawn always stays on. Any ideas on how to turn it off? Thanks, John

Well, I reset mine last night. Looks like I need to Upgrade to POLISY Regards, John

Under MAIN, Left Panel - two of my devices are showing in BOLD, while all the others are normal text. What does the BOLD mean?

Hi Geddy, Thanks, I was able to transfer settings manually without doing the front page login, and it worked. Thanks for you tips! Regards, John

I transferred MobiLink to another phone and it will not let me log in, says invalid user credentials. Worked fine on old phone. Regards, John

Dennis, Yes I do have ELK RP, I will give it a go! Give mem a couple days and I will write back. Regards, John

So I did a couple tests, - When the program evaluates true, the message comes - When the message evaluates false, the message is not sent. I need to determine why the program does not evaluate true every time. The trigger is setting the ELK to Armed away. I have a 3 min delay to allow me to get out. The only variable I can think of is how long it take me to get out and the last door closes, but as long as I take less than 3 minutes, it shouldn't matter. Stumped, John

The log only shows sensors/actions. Nothing on notifications being sent or program actions.

Thanks Mr. Bill, will do. Mine was set to 1000, so Last week I set it to 2000. It helped, but still not getting all notifications. Will bump it up some more.

So I am using the program and after running it for many months, it sends the notification about half the time. Should I increase the delay to 4 seconds? I have the ELK send the same message and I always get that one. If Elk Area 'Apt 1102' 'Arm Up State' is Armed Fully And Elk Area 'Apt 1102' 'Armed State' is Armed Away Then Wait 3 seconds Send Notification to 'Default' Else - No Actions - (To add one, press 'Action')

Will I be able to access my ELK using this app (now or in the future)?

I have the same exact issue, Firmware and UI are same. Email settings good. Will try increasing the timeout. Text is especially bad, sometimes hours late or no delivery at all. I setup a daily email and txt test at 8:00 every morning to follow timing or no receipt. Using gmail for ISY and Comcast for ELK. John

I have been using alert variables for my email messages. Been working OK for Name and Control identification for door, window and such. I also use the same alerts for water sensors. So I got a weird email that said ST 22. Couldn't figure it out, so I went in ISY and determined it was a water sensor. So why does it work OK for doors and such, it says for example 'garage door normal' but for the water sensor it said ST 22. The statements I am using are: Alert.Action and Alert.Control These used to be in the wiki in the email substitution variable section, but I can't find them any more. Thanks, John

dbwarner5 I tried that but it didn't work properly. The example from the wiki does work. Regards, John

jfai, OK I can see that. But what programmer would recognize that and is it dependable? I'm not used to getting in the 'then' statement then dropping out..... Time for some comments in the program! Also I would suggest adding that info to the wiki. Regards, John