JSchumann

When I try to use the IP address listed under: Internet access, I get this message: Your connection is not private. Attackers might be trying to steal your information. NET::Err_Cert_authority_invalid This concerning - what do I have set up wrong? I went to load a certificate, but dialog box opens asking where to load it from??? Port 443 is forwarded in router and Mobilinc works OK Thanks, John

What exactly does the portal give you?

Brian, I looked, no luck. I did take apart a spare I had and it has two holes labeled R/Vio.....red violet? Unfortunately I don't see 2 reds or I would hook up and ring out......Can't find a good schematic for the thing. R8184G1286.

Larry, I actually have a temp detector on the outlet of the furnace on the water pipe. The reset button idea was for faster notification there is a problem. I had some pipes freeze last year because the furnace tripped and went unnoticed for a while (was at work) when the outside temp was negative 5 for about a week.

Thanks Brian, after more investigation, Honeywell makes a model with isolated alarm leads.....Guess I will be dropping $100 to get one......Model R8184G 4066 (15 second version)

Oil burner has a red reset button that shuts down burner if there is an issue. I want a notification if the reset button popped (is open). I suspect the button is basically open / close 120v.......how could I connect to this to receive an alert? Regards, John

Thanks all for the input. I found these which will do the trick and inexpensive ($10): http://www.senasys.com/shop/product/2570f108/ Regards, John

I installed a radio shack relay http://www.radioshack.com/125v-ac-10a-dpdt-relay/2750044.html with mounting base http://www.radioshack.com/socket-for-10-amp-plug-in-relay/2750220.html on the box and wired the coil to the alarm light. Use the contacts as A or C and connected to ELKM1G alarm panel and use ISY to monitor. If no ELK you can use http://www.smarthome.com/i-o-linc-insteon-2450-low-voltage-contact-closure-interface-1-in-1-out.html to connect the output of the relay. I didn't use Synchro Link because if it fails you have no local or remote alarm.

I don't see the sale price...

Stusviews, That looks like it would do the trick, great suggestion! I was also looking at elk-m1ztsr

I had a problem with my oil burner last year where the igniter died so the furnace wouldn't start. Wife didn't notice problem and one of my loops froze befor I could fix the igniter. What product could I use to monitor copper pipe temperature and set an alarm if it goes below 140 degrees (I think the furnace is set to keep the water temp 160 to 180). Any help appreciated. Thanks, John

I have the Elk module, will go poke around, Thanks

I want to get a text or e-mail when my ELK keypad temp goes below a set amount. Is this possible? Thanks,

Thanks....I can probably use the I/O link and connect directly to ELK M1, when relay drops out NO contacts will close.....

I have a sump high level alarm (hooked up to ELK M1) that plugs in an outlet....recently the breaker tripped and I didn't get a high level alarm. Is there a module that I can rig to tell me if the alarm circuit lost power? Thanks, John

LeeG Thanks, you are right. I didn't have a trigger in the program. Thanks!

I have a simple program to start two other programs when sump alarm activated. First one starts, second one doesn't. If Elk Zone 'Sump' is violated Then Send notification to 'ATT text' Content 'Elk M1 Alert' Enable program 'Sump restored' Enable program 'Sump Audio' Sump restored started sump audio did not. What am I doing wrong? Thanks,

No, an outdoor light controlled by two 3 way switches....I want to put the micro behind the light. Any idea how to wire it ....need line and load then sense to the hot for the light?

I want a device that will sense when a light (has 3 way switches) is on or off and send a signal (controller). Would the micro on/off module do that? Can I hook one of the sense wires to the light (no connection to load terminals) to get the desired effect? Or am I doomed to put two insteon switches in my 3-way circuit? Regards, John

Is there a simple insteon device that will sense if a 120V unit is on or off? Thanks, John

Well I had to see it somewhere? I use that and alert.control I know I saw them somewhere.....what other ones are there? Regards, John

Michael, Where is the use of ${alert.action} documented? Looked in the wiki, no luck. I am currently using it but interested in what other options there are. Thanks, John

LeeG, Figured it out. Did what you said and found out each of the 7 has it's own number. So when I put that number in the message, that is the one sent. I wanted the message to send the notification for the node that tripped. What I had to do was change the message from: ${sys.node aa bb cc 1.name} to ${sys.node.#.name} The # pulls in the tripped node and sends it in the message. Thanks

Well some progress. The ISY links table does show a 1 (aa.bb.cc.1), so I put it in the customization. Now the message shows the node number and the word Smoke (when I press Test). I was hoping that the appropriate of the 7 names would show up Test for Test CO for CO and so on

LeeG I saw that in the Wiki, but the ISY only shows format aa.bb.cc in the Main tab.