JSchumann

OK, I checked this, both are set to 1.2. Now I have to wait and see if it gets shutdown. Thanks Techman for the info!!! Regards, John

I was notified by Xfinity that email won't work any more unless TLS 1.2 is being used (vice 1.1). I looked at my settings Configuration Email/Notifications Settings/Groups and there is only a checkbox to use TLS, it doesn't offer an option for version. I have V5.3.0 2020-10-01-14:39:56 for both Firmware and UI Any advice, I want to keep Comcast, not use Gmail. Thanks, John

Interesting idea! Thanks

I bought some used Motion sensors 2842-222 and it appears they were used outside and the stickers with the address are gone. I looked all over the device, took it apart and looked at the board with no luck. Is there a way to link them without knowing the address? I tried the new insteon device, and also the start linking icons. Thanks, John

Thanks, That is a different start guide than I have......

Oh cool, will try it. Where are the button sequences documented?

Got it. Thanks

Correct, I have it off I think. The box is blank......previously had ON.

Motion

Ok, so I moved the DIP setting to off. The dusk to Dawn notification is blank now (doesn't say Off). So it should work as a room sensor now. Thanks, John

Yes, UI Matches

Motion Sensor 2842-222 ISY 994i 5.3.0

In the Right screen for my motion sensor, Dusk to Dawn page, Status says ON. I cannot get it to turn off. This sensor is used in a room. Jumper Pin 3 is open, so it is NOT in night only mode Jumper pin 5 is closed, so I have Remote software enabled. In options I have sensing mode unchecked, on command only unchecked and night only mode unchecked I have written changes to device. Status for dusk to dawn always stays on. Any ideas on how to turn it off? Thanks, John

Well, I reset mine last night. Looks like I need to Upgrade to POLISY Regards, John

Under MAIN, Left Panel - two of my devices are showing in BOLD, while all the others are normal text. What does the BOLD mean?

Hi Geddy, Thanks, I was able to transfer settings manually without doing the front page login, and it worked. Thanks for you tips! Regards, John

I transferred MobiLink to another phone and it will not let me log in, says invalid user credentials. Worked fine on old phone. Regards, John

Dennis, Yes I do have ELK RP, I will give it a go! Give mem a couple days and I will write back. Regards, John

So I did a couple tests, - When the program evaluates true, the message comes - When the message evaluates false, the message is not sent. I need to determine why the program does not evaluate true every time. The trigger is setting the ELK to Armed away. I have a 3 min delay to allow me to get out. The only variable I can think of is how long it take me to get out and the last door closes, but as long as I take less than 3 minutes, it shouldn't matter. Stumped, John

The log only shows sensors/actions. Nothing on notifications being sent or program actions.

Thanks Mr. Bill, will do. Mine was set to 1000, so Last week I set it to 2000. It helped, but still not getting all notifications. Will bump it up some more.

So I am using the program and after running it for many months, it sends the notification about half the time. Should I increase the delay to 4 seconds? I have the ELK send the same message and I always get that one. If Elk Area 'Apt 1102' 'Arm Up State' is Armed Fully And Elk Area 'Apt 1102' 'Armed State' is Armed Away Then Wait 3 seconds Send Notification to 'Default' Else - No Actions - (To add one, press 'Action')

Will I be able to access my ELK using this app (now or in the future)?

I have the same exact issue, Firmware and UI are same. Email settings good. Will try increasing the timeout. Text is especially bad, sometimes hours late or no delivery at all. I setup a daily email and txt test at 8:00 every morning to follow timing or no receipt. Using gmail for ISY and Comcast for ELK. John

I have been using alert variables for my email messages. Been working OK for Name and Control identification for door, window and such. I also use the same alerts for water sensors. So I got a weird email that said ST 22. Couldn't figure it out, so I went in ISY and determined it was a water sensor. So why does it work OK for doors and such, it says for example 'garage door normal' but for the water sensor it said ST 22. The statements I am using are: Alert.Action and Alert.Control These used to be in the wiki in the email substitution variable section, but I can't find them any more. Thanks, John