garybixler

Try control instead of status.

Was wondering if there might be a Z wave connection map available at some time in the future. Would be great to visualize the Z Wave network to determine if and where a repeater might be needed. Also to see a device's neighbors. Thanks Gary

Yes I forgot to mention that I use the browser for device management but need to go to the app for routines and such.

I'm wondering if the difference in disabling and reenabling the skill might be if it is done through the app or a browser. I used the browser and didn't lose any routines or devices. I did need to add the devices back into the routine and enable the routine.

I did have the same issue and am working again. Other than an upgrade the disable and re-enable is suppose to fix the issue with 5.4.0. I can't verify that because mine was fixed before that was known. I had upgraded to V5.4.0_2 which so far has fixed the issue. A skill disable enable may be necessary.

@tmorse305 I think what was ment is to disable and re-enable your motion sensors on the ISY.

One thing that has worked for some is to go to your Alexa app and disable and re-enable the device. If that doesn't work an upgrade may be needed. Also there is a 30 sec timer on the device to prevent bouncing. So it may not work immediately.

If looking from the top of the board in the correct orientation the leds are marked d4, d5, d6 with d6 being the the third led. It would be the left led if viewed from the front. Just my guess. Still can't get the 6* push to work.

@macjeff With further testing I see the switch on Alexa turn on and off with the variable change. So the problem must be in the return response from Alexa.

I too discovered that variables aren't triggering Alexa responses.

I upgraded to 5.4 using SSH and have the rapidly blinking left LED. Gary

Hi, Just wondering if there would be any interest in creating a Genmon node server on PG3. Thanks Gary

Hi, Just tried V 3.1.3 and found one issue. When the leak sensor (Type 34) is queried the tag web site sends a notification that it could not call URL for "LeakSensor 5". I copied the info from that query. The other tag types work fine. Thanks Gay New Text Document.txt

Good News. All seems to be working perfectly. Thanks So Much. Gary

Did close and reopen AC several times just to be sure. I sent the Log. Thanks Gary

OK also this is what the AC shows.

Basically the AC is blank. It doesn't appear that any changes are loaded into the NS from the tag. I raised the temp on the tag but no changes were seen at the NS. Also GV12 doesn't change when wet.

I already had the leak sensor installed but the NS doesn't seem to see it as a leak sensor after update. It acquires the tag type of the last tag viewed. I tried deleting the node in the NS reboot and discover but can't get the NS to recognize the leak sensor. Basically no data is loaded into the ISY. I think it is present in the NS. I attached a snippet. Thanks Gary

That's odd, I have just tested the 'Seconds Since Updates' and all seems to be working perfectly. I Covered the tag with foil and after 5 mins or so it went out of range. There may be up to a 30 second delay until the NS server gets the out of range. I assume that is the polling interval and out of range doesn't trigger an immediate update. Thanks Gary

I couldn't say. I have never tried removing the battery.

@JimboNot sure if removing the battery will result in out of range. What I do is wrap the tag tightly in aluminum foil for testing. Usually the tag is in my car for determining if it is home or away. I set the tag to record every 30 seconds to give the fastest response and if out of range to search every 5 minutes. I query the tag from a driveway sensor so it would never need to wait the 5 minutes. As the out of range may take 5 minutes or more I tried using the 'seconds since update' but was to inconsistent. Hopefully the update will work better. Thanks gary

@Jimbo I have noticed a few discrepancies with some of the Tag parameters that doesn't follow the WEB sight. If a query or set light on/off is done the 'Seconds Since Update' always goes to 3600 until its regular update. If going out of range 'Seconds Since Update' will restart at 0 when 'Out Of Range' goes True. On the WEB site the count continues with no reset. Also the 'Signal dbm' doesn't reflect properly. I was thinking of using the 'Seconds Since Update' parameter in some programs but it is not consistent. Just a little feedback. Thanks Gary

@Jimbo GREAT NEWS! I installed version 13 and clicked "Monitor Tags True" and everything loaded right away with all correct date. Thanks so much for all your hard work. Gary

Thank you so much. Some NSs where deleted in PG2 but not uninstalled which are now. I don't think that made any difference however. Gary

It should be visible as the name assigned to your tag manager at your wirelesstag account. Mine was Home.