drprm1

I thought that in the app if I disable no motion state that it would just send motion (on) commands but it doesn’t.

In AC under a motion sensor it has buttons for “motion, no motion, and query” They don’t seem to do anything. Also have options for “motion and no motion” under programming but when used in a program they do nothing… I would like to be able to send an only on command (motion) from sensor like I could with Insteon ms. Thanks

Use an Alexa routine. Use whatever phrase you want to call on the program

Have you rebooted EISY. I suggest power cycling it…. Or

Well if all you want to see is what is available go here https://polyglot.universal-devices.com/ But I’m sure you’ll want to purchase some

You can use the find/replace in program view and run through all to see which programs a certain device is in.

Is the “all on” command in the PLM or in devices? I’ve had many “all on” events over the years. I did everything prescribed to mitigate them but would occasionally get one. I noticed it only affected my older devices. After EISY and new PLM I haven’t had one in some time till last week. 2:00 am and everything (old and new devices) came on. Hard to explain to wife what was going on 🙄. Very annoying

Probably more predictable to use Hue Plugin with Hue hub...

The integer variable did it Thanks!!

I'll try this

no keypad available... Tried this for a business window of 5 min but it would never change the variable back to 1 Patio Garage Door Therm Close - [ID 0028][Parent 0001] If $sPatio_garage_door is 1 And 'Patio Garage Door YL' Door State is open Then $sPatio_garage_door = 0 Set 'Patio GD Relay YL' ON command Wait 5 seconds Set 'Patio GD Relay YL' OFF command Wait 5 minutes and 20 seconds $sPatio_garage_door = 1 Else - No Actions - (To add one, press 'Action')

Was thinking about that. Why would that work?

Have written tons of programs but this is getting me... Issue: I have a patio overhead door that I'd like to have automatically close at certain temp and open at certain temp. I made two programs to set a variable to cold $sPatioGarageDoor=1 or warm $sPatioGarageDoor=2 and use these in my program to open or close the door.Here is the close program. (PatioGD Relay YL is my use of Yolink to control door over MyQ. Works great!) Patio Garage Door Therm Close - [ID 0028][Parent 0001] If $sPatio_garage_door is 1 And 'Patio Garage Door YL' Door State is open Then Set 'Patio GD Relay YL' ON command Wait 5 seconds Set 'Patio GD Relay YL' OFF command Else - No Actions - (To add one, press 'Action') My issue is that if I want to let the dog out for some business when it's cold out the door opens and the close program shuts it immediately. I've written a few programs to try and get around it but need help........... Thanks!!

Awesome

In reference to the program “Alexa turn ON xxx” runs Then ”Alexa turn OFF xxx” runs Else https://wiki.universal-devices.com/index.php?title=ISY_Portal_Amazon_Echo_Integration_V3#Programs

Under IOx configuration on toolbar, are you connected to your eisy?

Fixed mine. Thx

Back in business here too. Thx!

Have power cycled a few times. As stated earlier that reinstalling would be next and that I'd rather not. (i know not a giant task) but Panda88 said I shouldn't have to.

on PG3x

I don’t see anything in the Polyglot log. PG3 related? Started with this update so would think problem lies there? Would like to hear if this happened on anyone else’s PG

Reinstalled to same slot. No changes Still showing disconnected. When hit Start still says it’s already running. still no log

Never reinstalled, pretty sure just updated…. Tried to download log and I get a red pop up message saying “Error, file not found………”

Power cycled eisy with no change. Not sure what procedures used. Think I just updated from purchased ns store then installed?? Later on I purchased and installed again just to try. Can’t get log to show anything… When I hit “stop” there is a message and progress bar showing it stops. When I hit start there is no message or progress bar…If I hit start again it just says “ns already running” If I hit “restart” there is no messages or progress bars. About to delete and reinstall but rather not.