asbril

I don't know if this helps, but when I installed this wonderful nodeserver, when I click on the authenticate link I do that with right click and "Open link on new tab". That way I can easily do a copy paste of the authentication code into the nodeserver configuration.

That is a good point @tazman. I have my Tesla setup to de-activate Sentry mode while at home. The Sentry mode uses considerable energy, so @someguy's 7 day use at the airport parking would make perfect sense if using Sentry mode.

Bingo ! Thanks

Dialog boxes working again but deleting ns not working.

"Confirm" and "Cancel" are greyed out. In fact the same with Restart PG3, and I had to power cycle eisy to get the upgrade.

Thanks @bpwwer

1. The good news....... : It's not me 2. The bad news...... : a bit of annoyment

I understand what I did wrong (deleting NS from AC), but what do I do now ? Thanks for your help pg3_3-16-2023_21737-PM.zip

This is what I have now...... When I was not able to remove the not working nodeserver in slot 21, I added it (also) in slot 19. After a while it occurred to me to replace the Tesla "Refresh Token", a specific requirement for the Tesla ns and the nodeserver started to work again. Now I need to remove the Tesla ns from slot 19, but it does not let me. Maybe I need a sudo command ????

My Tesla nodeserver stopped working and restart did not help. I decided to re-install the ns and first deleted it from the Administrative Console and then pressed delete in the PG3 Dashboard. This is what I get : I tried several times but no luck. What should I do ? Thanks

Others may know better than me, but sometimes more nodes appear when you do a Zwave - Synchronize - Update with interview. At least it is something that I have seen. And in some cases more nodes appear after an exclusion/inclusion. Probably not the way it is supposed to be, but remember that the fact that there are different manufacturers may create challenges for UD, though they try to cover as much as they can.

I believe that it is a known issue that likely will be resolved in a future update. I would not worry too much about it. When there are sgnificant updates there is always mention in this forum.

Yes, same here.

For whatever reason my eisy suddenly became very slow to respond to commands. I am not aware having changed anything that I could think of which may have caused the slow response time. I rebooted eisy but it was still slow and then I power-cycled the eisy. As with the reboot, after the power cycle it took some time to synch everything and initially it was still slow when the synch window closed ended. After another 15 to 30 minutes, the eisy response time was back to normal and now I realize that even though the synch window closed after some time, the eisy was still busy in the background which impacted the response time. Probably, that may have been the situation after the reboot and the power cycle (in this case) may not have been necessary. In other words (and this is my tip ) , restarting eisy may require more time than the synch window shows.

Javi is super responsive and does a great job with UD Mobile.

If Quebec had listed to Charles de Gaulle it would now be on Paris time

Don't hesitate to describe what you would like to achieve and I'm confiident that in this forum you will get suggestions.

Did you try a reboot and/or power cycle ?

Keep us informed 😁

As I have the HA Yellow Box, I am tempted to try out Zigbee especially as I noticed on Amazon that Zigbee devices are significantly cheaper than Zwave. However, adding another eco system may be a pain. So maybe I just wait to see if Matter takes off,

I was using a RPi 3. I am not that techie and for me getting the front loaded (HA) Yellow Box was the easiest rather than getting another device and load HA myself.

Theoretically you are right but the restore did not intially work for me and I had to make a new backup. After that, smooth sailing. Though difficult to be sure, my impression is that with the Yellow Box reaction time of eisy based devices is faster, like immediate.

Thanks @Mecheng70 I have been using this for quite some time already. Very useful.

The first has come and will be served

My eisy has now been stable for well over a month, including all up-to-date upgrades. Therefore it is time to put my Polisy out to pasture and if anyone wants my Polisy then I'll be happy to give it away (shipping cost only). BTW my HA Yellow Box is also stable, so my old RPi 3 goes into the closet for any potential future use.