tmorse305

Thanks @bpwwer, I'll do that.

Hi @Panda88, I install the Blink NS and am not sure I have it configured correctly. I have a Blink XT2 which may be a camera model that you haven't incorporated yet. I attached the log after updating the camera. I have a Sync module but the NS could not find the camera when I enter the name 'Sync Module' in the configuration. I didn't give the Sync Module a new name in fact I'm not sure that's the name, I don't see any way to change it in the Blink app. When I tried 'NONE' it found the camera. It is partially working, the temperature seems to be correct, but I cannot control the Arm Status. I can change it in the AC but it does not change the actual camera status. Thank you for developing this NS! Using it will allow me to eliminate a work around using a Hubitat to allow IoP to monitor camera status Blink_10-13-2022_94051_AM.zip

Hi @bpwwer, VUE will not restart after I upgraded to 3.1.11. I tried to delete the NS and add it back but still no luck. Log is attached, there are many errors showing. Thanks for your help with this. VUE_10-13-2022_85819_AM.zip

Upgrade to PG3 3.1.11 fixed the problem

Hi @Panda88, I tried to install the node server(trial) but I get an error, see attached. The NS actually looks like it installs. It appears on the dashboard but only for a few minutes but then disappears as though it was never installed. The process is repeatable. Suggestions? Thanks Update. I tried to restart PG3 to see if it would make a difference, it did not. PG3 log attached from PG3 reboot. I see 1 error related to Blink: 10/12/2022, 19:27:01 [pg3] error: createNS: ReferenceError: status is not defined at checkLicense (/var/polyglot/node_modules/@universaldevices/pg3/lib/services/node servers.js:688:95) at process.processTicksAndRejections (node:internal/process/task_queues:95:5) at async Object.createNs (/var/polyglot/node_modules/@universaldevices/pg3/lib/services/node servers.js:451:5) log from boot.zip

Are you using a whole house surge suppressor? That might help if you don't have one.

Update: I don't think this is a NS problem but more fundamental with IoP. I'm going to create a new thread to see it anyone else is seeing this problem

Anything Insteon with a clear backing is easy to tell because the antenna is visible if it's dualband.

@Jimbo.Automates, I noticed my notifications coming through do not include actual data just the outline for what the message should be. This use to work: Notify Test sys_short - [ID 00C9][Parent 007A] If 'Greatroom / Ecobee Controller' Node server Online is Disconnected Or 'Greatroom / Ecobee Controller' Node server Online is Connected Then Set 'Notifications / Notification Controller / Service Pushover HomePush' Device Tims_Phone Set 'Notifications / Notification Controller / Service Pushover HomePush' Priority High Set 'Notifications / Notification Controller' Short Custom Content 16 Notfiication ID Set 'Notifications / Notification Controller / Service Pushover HomePush' Send Sys Short (old from controller) Else - No Actions - (To add one, press 'Action') There are a 2 other choices for the send command, the one above is the only one that does anything. The others send no notification at all: Send Sys Short with Params Send Sys Short Did something change? Thank you Update: I also tried this version of the program, same result, no data in notification. However the Send Sys Short does send a message. I noticed there was an error in the log 'Message is blank" so that was why I changed the program. Notify Test sys_short - [ID 00C9][Parent 007A] If 'Greatroom / Ecobee Controller' Node server Online is Disconnected Or 'Greatroom / Ecobee Controller' Node server Online is not Disconnected Then Set 'Notifications / Notification Controller / Service Pushover HomePush' Device Tims_Phone Set 'Notifications / Notification Controller / Service Pushover HomePush' Priority High Set 'Notifications / Notification Controller / Service Pushover HomePush' Short Custom Content 16 Notfiication ID Set 'Notifications / Notification Controller / Service Pushover HomePush' Send Sys Short Else - No Actions - (To add one, press 'Action')

If you're talking about Insteon leak sensors then just press the button on top of the sensor. Look in the AC, the wet and dry nodes should toggle on/off with each button press. Leave it with the dry node "on" . Then place the sensor on a wet sponge and it should toggle to wet.

@Javi, thank you for widgets in iOS! So far all of the new widget types I've tried are working great. I did run into one problem which I don't think is related to the widgets. I added a program to the favorite screen, and when I go to save it after changing anything I get this error. But if I discard the changes when I get back to the favorite screen the changes have been made and it is operational. I tried a 2nd program and got the same result.

No! I figured it was a setting somewhere, thank you for pointing it out!

@Javi, this is great, thank you! I have several variables displayed on my Favorites and it's great to be able to change the status value from 0/1 to On/Off. I have one general question. When I first open the Favorites page not everything populates with the current values. I have to tap on them to get the value to display. Is there a way to get them to all show up initially. Thanks again for your continued development of UD Mobile. I can't remember the last time I opened MobiLinc!

@bpwwer, thank you! Re-install was successful.

Thanks @bpwwer, Here is a bit of the PG3 Log. The only error I can see is: 9/19/2022, 17:05:07 [pg3] error: [August(10)] :: STDERR: python3: can't open file '/var/polyglot/pg3/ns/000db9561078_10/./august_poly.py': [Errno 2] No such file or directory I already tried to re-install but no improvement. Log attached August NS restart.txt

@automationgeek, I did the 3.1.8 PG3 upgrade today. All of my NSs started except the August Lock NS. It will not start and is not producing a log file so I can't provide any more information. I've tried deleting it and re-installing but no luck. Is anyone else experiencing this? Thanks in advance for any suggestions.

pg3_9-19-2022_14803_PM.zippg3_9-19-2022_14803_PM.zipI did exactly the same step as @wrj0 did above but now none of the NS will run. I have tried to restart PG3 and individual NSs but no luck. Suggestions? Thanks. Partial log attached, the whole file was too big. Update: I opened a ticket based on @bpwwercomment below. Based on @JimboAutomatescomment above I re-ran the upgrade and many of the NSs restarted successfully. I reinstalled one which fixed that one but the last one (August Lock) will still not run. I'll also note that the AC is running very sluggishly. pg3-current.zip

Thank you!!!

Sorry if this is covered somewhere but I looked and couldn't find it. The iOS app store shows that I am running the latest version but the version is 0.8.4 which is not the latest. How do I update to the latest version? Do I need to use TestFlight? Thank you.

Strange problem. Maybe try deleting the portal scenes one at a time and see if it stops.

@tazman, Just one more thing to break...

@tazman, If you can't wait for a PG3 solution, there is an integration on Home Assistant for Vue. I don't use HA but I thought I'd try it to see if it worked. It was pretty easy to setup and it works as advertised. I created a quick automation to notify my phone when the dryer stopped. A friend asked if I could create notifications for her washer and dryer and I have been trying to come up with a simple solution. Rpi and a Vue would do the trick. As I understand it there is an ISY integration that allows data to flow between ISY and HA. No expert here, I now have about 60 min of experience with HA!

Same here. Tag updates also late. Interestingly if I can update them manually without issue.

@CPrince, How did you pair them? Using ISY or just device to device? Maybe that pairing is enough to disable the wireless programming? Try a factory reset and then see if you can program the wireless thermostat before you pair it with the main one.

Could it be related to the second statement from the manual: IMPORTANT! Day Modes only function when the Insteon Wireless Thermostat is connected to the optional power adapter. Once you have added Insteon Wireless Thermostat to a scene in Insteon Thermostat as a wireless temperature zone, the Program button will no longer function. All program controls will be performed on the Insteon Thermostat.