tmorse305

I just purchased the ISY Portal today, planning to move away from Mobilinc Connect (IOS) as I purchased an Echo today. I configured it without an issue then went to the Mobilinc forum looking for help on configuring Mobilinc to work with the portal. Instead I find an announcement that Mobilinc now works with Echo! I cannot keep up! Can I switch back to Mobilinc Connect portal. Too bad I didn't know this before I burned $50 on a new portal.... Thanks, Tim

Thank you for the replies. I'll try connecting to ISY without using Mobilinc Connect and see what I lose. Tim

I'm also considering an Echo and am currently using Mobilinc Connect. When you said you lose push notifications, do mean notifications generated by the Mobilinc App, for example the Geofence notifications? What other features are lost? Thanks, Tim

I just got home to find the vast majority of my lights and and both garage doors open. Very unsettling to say the least. I have had many Insteon devices in use for years with other controllers and never had this problem. Then I find this thread where Blackbird had a similar problem today. Does the "All On" command also trigger I/O Link devices?

Upgrading to 4.2.30 solved the problem. Thank you very much for your help!

Here is the log file for a motion off then motion on: Sat 09/12/2015 09:47:35 PM : [iNST-SRX ] 02 50 37.A4.56 00.00.01 CF 13 01 LTOFFRR(01) Sat 09/12/2015 09:47:35 PM : [std-Group ] 37.A4.56-->Group=1, Max Hops=3, Hops Left=3 Sat 09/12/2015 09:47:35 PM : [ 37 A4 56 1] DOF 1 Sat 09/12/2015 09:47:35 PM : [ 37 A4 56 1] ST 0 Sat 09/12/2015 09:47:36 PM : [iNST-SRX ] 02 50 37.A4.56 00.00.01 CF 13 01 LTOFFRR(01) Sat 09/12/2015 09:47:36 PM : [std-Group ] 37.A4.56-->Group=1, Max Hops=3, Hops Left=3 Sat 09/12/2015 09:47:36 PM : [iNST-DUP ] Previous message ignored. Sat 09/12/2015 09:47:36 PM : [iNST-SRX ] 02 50 37.A4.56 13.00.01 CF 06 00 (00) Sat 09/12/2015 09:47:36 PM : [std-Group ] 37.A4.56-->13.00.01, Max Hops=3, Hops Left=3 Sat 09/12/2015 09:47:36 PM : [iNST-INFO ] Previous message ignored. Sat 09/12/2015 09:47:36 PM : [iNST-SRX ] 02 50 37.A4.56 13.00.01 CF 06 00 (00) Sat 09/12/2015 09:47:36 PM : [std-Group ] 37.A4.56-->13.00.01, Max Hops=3, Hops Left=3 Sat 09/12/2015 09:47:36 PM : [iNST-INFO ] Previous message ignored. Sat 09/12/2015 09:48:50 PM : [iNST-SRX ] 02 50 37.A4.56 00.00.01 CF 11 01 LTONRR (01) Sat 09/12/2015 09:48:50 PM : [std-Group ] 37.A4.56-->Group=1, Max Hops=3, Hops Left=3 Sat 09/12/2015 09:48:50 PM : [ 37 A4 56 1] DON 1 Sat 09/12/2015 09:48:50 PM : [ 37 A4 56 1] ST 255 Sat 09/12/2015 09:48:50 PM : [iNST-SRX ] 02 50 37.A4.56 00.00.01 CF 11 01 LTONRR (01) Sat 09/12/2015 09:48:50 PM : [std-Group ] 37.A4.56-->Group=1, Max Hops=3, Hops Left=3 Sat 09/12/2015 09:48:50 PM : [iNST-DUP ] Previous message ignored. Sat 09/12/2015 09:48:50 PM : [iNST-SRX ] 02 50 37.A4.56 11.00.01 CF 06 00 (00) Sat 09/12/2015 09:48:50 PM : [std-Group ] 37.A4.56-->11.00.01, Max Hops=3, Hops Left=3 Sat 09/12/2015 09:48:50 PM : [iNST-INFO ] Previous message ignored. Sat 09/12/2015 09:48:51 PM : [iNST-SRX ] 02 50 37.A4.56 11.00.01 CF 06 00 (00) Sat 09/12/2015 09:48:51 PM : [std-Group ] 37.A4.56-->11.00.01, Max Hops=3, Hops Left=3 Sat 09/12/2015 09:48:51 PM : [iNST-INFO ] Previous message ignored.

The MS was in linking mode prior to the write attempt. Here are the screen shots you requested.

Jumper #5 is set for software control. Here is the Event Viewer dump: Sat 09/12/2015 08:33:02 PM : [All ] Writing 0 bytes to devices This single entry occurred after I tried to update an option

The only dual band device currently connected to the ISY is the PLM itself. The MS is about 6ft away from the PLM. Since I can read the motion, dawn/dusk and battery status I figure i was close enough. The HouseLinc is also connect via a USB PLM. I have many dual band devices in my house but I haven't linked any of them to the ISY yet. I was starting small just to get the feel of the ISY.

I just purchased an ISY994i IR PRO to replace a Cortexa (and some HouseLinc) automation controller. So I'm new to ISY but not home automation. I have a new motion sensor that I bought and have linked it to the ISY, it's the only device linked. I factory reset the sensor prior to linking and it is working correctly reporting both motion, dawn/dusk and battery(off) to the ISY. The problem comes when I try to modify the option settings. I set the led flashing on the MS then click the options button and I get an error message "Request Failed". Once the Option screen is open I click the query button but get the same error message. I linked it to my Houselinc software just to make sure the MS is working. From the Houselinc I was able to set to the options. So I think the MS is OK. Any suggestions? Thank you.