jkraus

Hi, I think there are some improvements in the amount of control of the KPL LED brightness in Beta versions, as I am at the official 2.70. I think 2.75 is out shortly so I will wait, but my basic question is what does it mean to have a range for example of 1-63? Is this for the off state or the on state or a relative number of the difference in the two state, as I only have seen one level for the setting in the ISY?

Yup, once you figure out the strange way to program it works great! Got 16 codes programmed and working! Joe

12 scenes? Can you give me a little programming example? Also, more work with the EZx10RF and I think I am getting it working. Have 5 codes now linked and seems to be working pretty good with a PalmPad and coverage is most of he house with pretty instant on due to it being Insteon transmitted rather than X10 Will keep you informed but crossing my fingers, seems to be now going pretty well. Joe

Hi MIke, I understand how to do that with programs, but do you have a program for evry code you use? What about brite and Dim, more programs for each one? Seems like it would be a lot, or is there some trick around the brite/dim? Joe

Well, you were right to caution me. While I got the first 3 codes to work, after that further codes just did not seem to work in the scenes. I am not prone to spend a lot of time on this, just wanted a controller that had more than 6 buttons. Anyone at UDI hears of something coming from SH? The RL is nice, but very sensitive to triggering (just picking it up you can brush some of the buttons and they trigger) along with the limited 6 buttons. Thanks Joe

Thanks! "The devil is in the details", but you have made it clear enough to get started. Since I have RemoteLincs to do the control today, this is a "non-mission critical" project, so I should have some fun playing with it. Thanks Joe

Hi Michel Maybe I do not totally understand the concept, so sorry for that. But why would someone want to add an X10 device? Is not the idea to control Insteopn devices (Which I am now 95% converted to) with X10 controllers i.e. in my case a PalmPad. I am not sure how to get started, but I will receive the EZX10RF today, so perhaps it will become obvious after that. Since I will receive it today, I assume it will be the latest firmware. One simple question. Is it "better" to assigning X10 addresses to Insteon devices or set up the EZX10RF to translate to the device's Insteon address by linking it. If the latter, do I do that "outside" of the ISY environment? Again, a little confused how to start Joe

Hi I asked about a month ago if the ISY supports the EZX10RF, and the answer was something like "not officially". I did not pursue then, but now have a EZX10RF on order and wasn't sure what "officially" meant. More specifically, can I link the EZX10RF to the ISY? I know that I can link the EZX10 to devices directly, but can I use X10 Palmpad to control a scene created in the ISY via the EZX10RF? Thx Joe

Thanks Rand, OK, make sense. I went ahead and added them while in my office. I mention that because I had a somewhat dead spot and recently added another AP to my office, so it may be why this time it did not take "forever", but still on the order of 3-4 minutes, perhaps that is normal. BTW they are not all responder, in fact 5/6 are controllers if that that makes a difference i.e. only one responder in this scene. Thanks Joe

OK, just seemed that if were making no change to the RL i.e. they are only controllers not responders (can an RLs ever be a responder?), they would not be involved in adding another controller (the 3rd KPL) to the scene. When my scene is even moderately large (6 devices are so) the link process takes forever, especially for the RLs

for example: Let's say I have a scene that is controlled by 2 different RL (each button A) and two different KPLs (each button A) and I want to add a 3rd KPL (say button A). Do I really need to go chasing my RLs down and set them to link mode? Can't I just add the new KPL to the scene?

Anyone know if SH supplies the Remotelinc plastic label covers, keep losing mine

Certainly no expert here, but the problem sounds vaguely familiar to my problem I had that when exiting the RL linking mode I pressed one of the key buttons, and this caused all sorts of problems. I was instructed to hit the "Dim" button on the RL to exit linking and it solved my problem. Hope that may help Joe

Perfect! Thanks. I had basically came to the same conclusion by trial and error, just was not sure that I was missing something more obvious. Thanks again Joe

sorry for my inexperience, but the only wayI see to turn off the KPL LED is to add the KPL button to a scene then turn off that scene at the end of the then path or the else path. Is that what you mean?

I naively thought when the program was done the KPL light would turn off. Now I have created a scene for the KPL button and in the program's else command I turn that scene off. Is that the best way?

well you say so, but I purchased TouchSwitch yesterday and have yet have not received any email with the program or instruction to download it, much less any coupon Joe

Thanks!

after this program executes the KPL on LED is still lit. How do I make sure it is in the off stage: This program is a 1HR Pool Pump" If Control '0A.2C.EE.1' is switched On Or Control 'KPL Pool Eq B' is switched On And Control 'KPL Pool Eq B' is not switched Off Then Run Program 'Pool on 2 HR KPL' (Else Path) Run Program 'Pool on 4 HR KPL' (Else Path) Run Program ' Pool Eq On KPL' (Else Path) Wait 2 seconds Send X10 'K16/On (3)' Wait 1 hour Run Program 'Pool on 1 HR KPL' (Else Path) Else Send X10 'K16/Off (11)'

Hi, I cannot find on the UDI site where to purchase this module. Rumored to be $4 for the TouchSwitch

If just using RL to control programs, would seem OK, but if wanted the advantage of the RL to control lights and do dim and brighten, it would be lost by using with programs I believe. Joe

Great, thanks! Implemented your suggestions and works great. Man, I keep learning the programming, but see the advantage of using the "Run Else" and your other suggestion. All is OK now, again, thanks Joe

This should not be this tough. I am trying to have two KPL button, B & D, that are listed as mutually exclusive turn on the pool pump for 1 hr or 2 hr respectively, but when I run the programs below by hitting Button B first then Button D, program B is still running If Control 'KPL Pool Eq B' is switched On And Control 'KPL Pool Eq B' is not switched Off Or Control 'KPL Pool Eq D' is not switched On Then Wait 2 seconds Send X10 'K16/On (3)' Wait 1 hour Send X10 'K16/Off (11)' Run Program 'Pool on 1 HR KPL' (Else Path) Else Send X10 'K16/Off (11)' If Control 'KPL Pool Eq D' is switched On And Control 'KPL Pool Eq D' is not switched Off Or Control 'KPL Pool Eq B' is not switched On Then Wait 2 seconds Send X10 'K16/On (3)' Wait 2 hours Send X10 'K16/Off (11)' Run Program 'Pool on 2 HR KPL' (Else Path) Else Send X10 'K16/Off (11)'

sorry, I do not understand "Program Test"

so thereis a selection calls "run else path"?. I will check when I get home. Thanks Joe