tlightne

Purchased and installed an additional temp sensor today and now all the sensors show and update properly in admin console Plugin nodes on EISY....

@bpwwer Ok thanks for looking into this. I may order another sensor from Ambient and add it as an additional sensor to see what happens...

@bpwwer Hi Bob, Main with address e8db84e738-1 is the outdoor array and is working as designed. indoor with address e8db84e738_2 is as labeled the indoor sensor and is working as designed. one with address e8db84e738_3 is a sensor in a chest freezer and is working as designed. Two with address e8db84e738_4 is monitoring temps in my bedroom and is working as designed. Three with address e8db84e738_5 is the temp sensor the is not being updated. Attached is the download Package. Thank you.. AmbientWeather_6-28-2024_63232_PM.zip

@bpwwer My Eisy crashed while upfrading PG3 to 3.2.27 and had to send it in to UDI to be reflashed. After returning and reloading PG# backups my Ambient Plugin loads all the nodes to my Eisy and the data gets updated except one an indoor sensor that I measure AC supply temps get any data. I have rebooted Eisy a couple of times with no luck. I have deleted the plugin from Eisy and PG3 rebooted EISY then reinstalled the plugin but still do not get the one node to update in EISY. I see the all the nodes in the AC console it just will not update the data. I have looked in the logs for the plugin and I can see the data get updated from the API. I have attached the log file here as well. EISY Firmware is 5.8.3 and PG3 is 3.2.27. Thank you.. AmbientWeather_6-28-2024_31954_PM.zip

Open a ticket with UD at this link... https://www.universal-devices.com/my-tickets/

I would wait too. Sure wish I did. I hit the update packages button around 2:00 this afternoon and have been out of the water since. I have a ticket open but have not heard anything from support yet...

Hit upgrade button in AC console and received two messages the upgrade was in progress. Waited 20 minutes no other messages received in AC console Finally received message upgrades complete. Never received message to reboot so waited 10 minutes and did reboot from AC console. Hit reboot button on AC console nothing happened. Waited 30 minutes hit multi function button on Easy to shoudown. After shutdown removed power waited few seconds and repower up and booted. Never received anything from Easy. Tried to SSH in and get connection refused. LOX finder says not found. Eisy does not show online in portal. I think I am hosed. I have opened support ticket..

@Goose66 I have downloaded the plugin but after spending a couple for days of attempting to get the Google side set up I was unsuccessful. I would love to see you persue and easier setup.

@bpwwer FYI.. Received this email today from Open Weather....

Mine pared with Eisy with no problem. Follow the instruction from Bali and the remote will work after you include them in Eisy..

@glacier991 Login to your account and scroll down you will see an API section with a "generate API button"

https://www.universal-devices.com/my-tickets/ Go here and open a ticket with UD..

There is only two nodes. Indoor and Main unless you have optional sensors.

@Goose66 Thank you...

@Goose66 I want to be able to open my blinds halfway. I would be able to open the blinds in a program then wait a specified time then stop. Thanks for consideration on this..

Installed three sets of Allen + Roth shades today and the Bond hub picked the up the shades with no issues also the Bond Plugin talks to them without any problems. My question it there are three commands in the Bond app Open Stop and Close. The AC only has two commands Open and Close. Can the Stop command be picked up by the Bond plugin?? Thank you

@Goose66 Any input to my previous post ?????

It is the same ID and password used to log into your Polisy/Eisy..

@Goose66 Installed three sets of Allen + Roth shades today and the Bond hub picked the up the shades with no issues also the Bond Plugin talks to them without any problems. My question it there are three commands in the Bond app Open Stop and Close. The AC only has two commands Open and Close. Can the Stop command be picked up by the Bond plugin?? Thank you

@KentinadaFrom experience not sure if it is in a WIKI someplace. I picked it up from reading posts in the UD Forums. A Zwave device can only be included in one network so if it was previously owned and returned by a customer or if Factory did a test on it and did not remove it properly it would still have the old network in it so it is best to always start with an exclusion first.

Did you do a factory reset or exclusion on the device before trying to include it. Tht is recommended even on new Zwave devices.

@Mike M I use Shelly RGBW2 controllers with generic strips With the shelly plugin. All works great I have not had any problems. Very reliable...

UUID sent..

@Javi Ticket opened...

Getting the following error when selecting My Notifications in UD Mobile. I open the app and select "My Home Connected" then select "My Notifications" it returns: {Successful":false,"errorCode"404,"errorName":"errorMessage":" This uuid is not an eisy uuid":"data":null} .404. I have verified my EISY UUID in portal. app version 1.1.53 also had the error with app version 1.1.41. Thank you