tazman

Here you can see the commands show up in both PG3 and the AC.

Did you install the Developer Packege from the AC?

It has been a long time since I set this up but my first thought on what you said is I don't think the harmony remote sends IR I think it sends RF commands to the hub and the hub sends the IR commands. When button presses are added they show up in the AC also. From what I remember the codes you are going to use need to be loaded to the Flirc from a computer to be used in ISY.

Great post @Javivery informative thanks for sharing!

Isy portal is needed if you're running the occupany items in the portal.

Try shuting down the eisy with 6 clicks of the multifunction button and unplugging the unit when the light turns red wait 10 seconds and give it a while to start then try accessing it. Sometimes eisy gets hung up and needs a complete power down to return everything to it's proper state.

I believe they can be deleted in ISY where you took this screen shot from. Click on each individual node server and I think there is a delete button in there.

Have you checked the link tables in the motion sensors? Maybe have the event viewer open on level 3 while you trigger the motion sensors?

Have you shutdown and unplugged your "ISY" device? That seems to be a step that can cure some "issues"

This happened to me a couple of times in the past and the only way I know to fix it was to submit a ticket with UDI and they would do something on their end to correct the issue.

As far as I know you have to use a control device/program/variable from Eisy exposed to Alexa with a Routine in Alexa or multiple Routines depending on how much control you want over the device in Alexa. The Virtual node server is the actual name of it. https://github.com/UniversalDevicesInc-PG3/Virtual/blob/master/README.md

You can have some control of Allexa devices from Eisy. You can expose a variable to Alexa as a motion sensor and there is the Virtual node server that you can create virtual switches to use in Alexa. You can also create Routine in Alexa where anything exposed to Alexa from Eisy can control Alexa devices.

I use the regular Ocupancy in the portal so I don't know if this applies but did you setup the configuration in the portal and upload the node definitions? I know when that needed to be done for me it would show the light bulb and I have had updates that required me to upload the node definitions again.

It was a different device but it sounds similar that you might want to try their solution

@CoolToysyour front door needs to be a control item not a status so when the door is opened it activates the program to run as long as the rest of the conditions are met.

Try pressing the button 6 times to power the unit down and when the light turns red pull the plug to remove power for a little then plug it back in to see if that helps.

Does your firmware and UI match in Help About? It sounds like you need to clear your Java cache.

I believe the portal one is if you are using the occupancy node server but I don't know if it is used by UD Mobile also. For the Invetory one you will have to delete from IoX using the AC.

OK let's try this again https://wiki.universal-devices.com/index.php?title=Polisy:User_Guide#Upgrading_to_PG3x

When you uncheck the Z-Wave support you have to click the save button before you restart IoX or else it does not hold the setting.

On the Configuration/System tab you need to check the box to enable Zigbee Support then press the Save button followed by the Restart Iox button.

The install went good for me I still get the PG3x restart needed but refreshing the browser now gets rid of it without having to shutdown eisy. Node server re-install: Restart node servers after re-installation if it was running Node server re-install: At the end, display a confirmation message The re-install worked with a green box confirmation afterwards. In node server nodes, property variable can be copied using copy icon This is a nice feature!

It was most likely triggered by the query program if you have it. I would disable the program so the only way it will run is when you run it directly from Alexa.

I ran the update on my eisy and everything seems to be working fine. After the commands and a restart of PG3x it still showed PG3x needed to be restarted so I performed the 6 button press shutdown and pulled the plug on eisy after the light turned red then after pugging it back in when it booted the restart PG3x was gone. I have made the 6 button press shutdown and removing power a standard step after an upgrade.

The update went fine for me and I'm able to log into PG3x where I see this image and I even performed the power down 6 button press and unplugged the unit. Everything seems to be working.