TheWabit

So I raised it 3 degrees with a hair dryer - I still cant get it to update. Crap!

I did press and hold the master button until it beeped and "master" appeared on the screen. however, I have no wireless units attached to it. I guess we will see what happens.

Hi Michel, It is Insteon and I DO get a change in Admin (set point number) after changing the set point manually. More times than not, the set point number updates but the temperature doesn't.

I cant say "never" It does sometimes. But then there are long periods (say 12 hours) where it wont

Additional information - when I query the tstat, it updates to current immediately.

Bonus Room Fan - [iD 0038][Parent 0001] If Status 'Upstairs Tstat' >= 77° (Temperature) Then Set 'Bonus Room Fanlinc - Motor' High Wait 10 seconds Set 'Bonus Room Fanlinc - Motor' Med Else Set 'Bonus Room Fanlinc - Motor' Off

2441TH

How often should the ISY get updated on the temperature and set status of the thermostat? I have looked often and noticed the ISY doesn't match what the tstat says. I have created a program with the fanlinc - the wrong information is not triggering the fan when it should.

I would create a scene of just your garage exterior lights. Use that in your "then" statement

Thanks Stu - But how does the < sign get in there? I dont see it under status. Disregard - I figured it out.

Hello I cant find what I am looking for in previous questions/answers. I have jumped into the fanlinc and thermostat world. I am trying to find some examples of programs that bring the fan on when in a temperature range and back off when outside that range. Anyone been successful with this? Thanks!

Problem Solved! I have the IO Linc wires soldered to portable opener circuit board switch. One of the wires came loose from solder. It was still really close and I am assuming that it was touching when the garage door started to go up but when the vibration started on the opener, the wire moved away from the solder joint. Anyway - re-soldered and all is well!

Thanks Larry - Only thing is when I manually go in the admin and change the variable from a 1 to a 0 and back to 1, it works fine. Someone just please verify Momentary B is correct and about a 2 sec hold time?

So here is a dumb question. I set this up awhile ago with Mobilinc. My Init state variable says "2" and value is "1". Is the "2" correct?

I will check into Mobilinc being the issue then. It has worked flawlessly everyday for a year - Thanks

Update - The PLM finally did fail. I got another one and all of the above issues disappeared. So I guess if a PLM is in the process of failing, there are some subtle signs.

I have new thing happening lately. When my mobilinc is inside the geo-fence, it sends the signal to open the door. The door opens about 2 inches and stops. Anyone seen this before?

So I am having trouble with my Fanlinc. I had it setup with a KPL. It was working fine then all of a sudden it would only go to medium. I deleted from the ISY, rediscovered it, I factory reset (before rediscovery). I have taken the KPL out of the equasion by removing all of the button scenes. So controlling through the ISY dashboard only - again only medium turns the fan on. Any other speed does not work. Anyone seen this or have any suggestions?

Maybe I will go try it again - I did play with timing in the ISY but I am not sure I paid attention to the wiring. I will let you know - thanks! BTW - I meant the slots in GDO - not the IOLinc, I know THAT matters.

I am glad you said wiring - I cant remember on my old GDO. Did it matter which wire from the IOlinc went into which slot (it is a slot on my new one but was just a screw on the old board)?

Ahh yes - I did try that first. The IOlinc clicked when I activated it but nothing else happened.

Do you mean combine the IO wires with the wall mount wires into slots?

So I have opened up the remote. Do the 2 wires from the IOlinc get soldered to that pushbutton connections on the board?

So in your experience, is the remote battery an issue?

Larry - This is just a change of openers. The sensing works fine (green light on when open/off when closed). I push the button on the IO Link and it clicks but no door movement. I try to operate it through the ISY and it doesn't move. But it sounds like - from Stu - that the contacts used for the Multifunction Switch cant be used like the older models.