larryllix

Yeah it should but this happens a lot being more of a purebred google device. That's not the first app that was refused entry and won't be the last on that one. It's half crippled. That app was the original one I downloaded in NY with a clean tablet and no Google accounts known on it, yet. Once I installed my google email account I was locked out of the app again, even while in NY. I switched over to another Android 4.4.2 device and the amazon alexa app just doesn't show any device control pages and only The device/group/scene lists. There are no Echoes/Dots in any of the lists. Only ISY known devices. The Alexa app is the latest version also. This isn't the first time this has happened where Amazon releases permissions to my area months after everybody else. Postal code permission and Canadian address permission only showed up a week ago. Seems I will just have to wait for some time. I don't have that many rooms involved yet anyway so "Turn On Bedroom light" or "Turn on Red Bedroom Lights" is not bad for now.

Android v6.0 CT9223W97-ANDROID6.0-V57-V1.15.33

grrrr....... I wish these companies would stop these wars that only hurt the customers!I just removed the app from this tablet and now get this..

Welcome to the forums!! I assume you must be using the ISY Network Resources module to attempt this. Are your individual (or any) devices working using the same technique?

For some Canadians....this may not be possible yet as there is no Amazon devices you can link into groups...stand by. (I don't have Join-In available yet either)

I have none of those screens found on an apple, but I am running v1.24.3096.0, wherever it came from. Matter of fact I cannot operate devices from the Android app at all. There is no page like that, just a list of devices with their Insteon addresses.

Canadian Play store? I didn't know there was such a thing. Is this an auto-switch thing or do I have to change over to it?

Interesting! "Switch On/Off" works perfectly for Echo Dots also. It seems like only On/Off count here as "Switch" was never mentioned before. Maybe it is reading ISY's mind?

Definiitely running v3 and all that was followed. I a running the Alexa webpage app on a linux Chromium, windows 7 IE , windows 10 IE, and also android app. No icons or Alexa appliances available for grouping. It should be noted that on the bigger screen computers there is no app to be had and the webpages know I am in Canada. As per Stu I will have to go back ad check my Android app again. Thanks!

Are we all talking the same skill here? I have v3 installed, forgot and rediscovered all my devices several times. This sounds like it is confused with an Insteon group procedure. I have no Alexa devices that can be selected in the Amazon app or ISY Admin Console and I have no light bulb icons (no icons whatsoever anywhere) in the Alexa app either? My Echoes and Dots are not selectable smart home devices, according to the lists, to be selected for inclusion in a group. Where are the Amazon devices being found? BTW:There is going to be much confusion in the future because any ISY element that is not a device is found under the "Scene" tab. I don't use many scenes but all my links to programs are labelled as scenes too. Now we have Zwave scenes, groups, Insteon scenes, ISY scenes, and Alexa scenes and groups.

AI at it's finest! Don't ever let google find out you automated your toilets! They will be flushing them just before you get home every time, so they are fresh when you get there! LOL

My apologees! This thread is about the limitations of open / close vocals.

I haven't noticed any difference between v2 and v3 so I dont understand the fuss r any of the benefits either. Multiple rooms still require multiple accounts and no accounts links can be changed that I can find. I don't believe I use any scenes directly but only devices and programs. Many programs control scenes, some via variable value changes. Program Offs work just fine in the "Else" sections so that the vocal syntax works out properly eg: .....Alexa..turn off ALL LIGHTS. works fine in the program Else section, turning on my Off scene.

https://www.aartech.ca/isy994zwup-zwave-upgrade-module.html

Motion sensor do communicate on the Insteon network. That is how they interact with other devices and ISY bi-bidirectionally, for almost every signal. When the MS sends out an On (= motion detected) another device sends back an ACK . When ISY sets up parameters the MS receives the settings and memorises them.

I have shopped through this skill, for hours now, and I see no way to connect to any other account than Amazon. Every account setting is the account name and password for Amazon, not what webpage. I have disabled the account completely and re-enabled it, as well as poked every instance I can find of account names in each device and the master skill setup. The URL or location is never an option. I'm lost.

All smart thermostats have this problem, more or less. The stat companies do not like to admit it, though. They all have some problem and until the electronics become more micro powered or as many have done now, offered remote sensors to get the sensing away from the heavy heat generating electronics. When you open up any stat from a company with more than a toy manufacturer experience, you will see reflective foil, and/or insulation used in an attempt to isolate the sensor from the electronics. Some stat companies have tried to compensate for the electronics heat generated by offsetting (mis-calibrating) the readings from the sensor. This works until a slight breeze comes along and takes the residual electronics heat from the sensor away. What you get now, is a differential On/Off of 4, 5, 8 degrees creating waves of heat and cold in the heated area of the stat. When the furnace runs the stat "feels" the fan draught, cooling the sensor, and the furnace runs too long, making any differential setting inside the stat a complete waste of setting menu programming. I have experienced this on about 4 brands of stats now. BTW:Never go by the displayed temperature on the stat front. The sensor reflects the compensated temperature the electronics goes by and can be many degrees off of a good accurate sensor (only) placed beside it at the same distance from the wall. Every brand does this out of the four I have installed in the last two years.... Honeywell, Venstar, Tekmar commercial. Insteon? I never look at the two I have anymore....mostly toys only good for emergency heat, ISY input metering, humidity but never home comfort without needing a sweater on and off 3-4 times per day.

In v3 the devices are divided up into groups of style of devices. Look in the other groups. Sent from my SGH-I257M using Tapatalk

I know this easy to do in v5 but I am not sure if v4 had a level set to a variable value option. Sent from my SGH-I257M using Tapatalk

Read post #4 If jumper 5 is on then all settings can be done in the ISY admin console. Sent from my SGH-I257M using Tapatalk

Your "Normal" program triggers are disabled. BTW: You could place that code in the Else section of the first program unless there is a hysteresis element by time delay or by temperature difference, effectively giving three states instead of two.

https://forum.universal-devices.com/topic/17495-how-to-use-a-ms-with-lights-for-faster-response/?hl=%2Bhow+%2Blights

Fred. For what I am thinking you are trying to accomplish and IF you have v5.0.10....we told you incorrectly in the logic of the first few suggestions. You could set a variable at the desired stat setpoint. Then in program logic set a condition NOT equal to that setpoint variable. Now you shouldn't get the program retriggering every time the stat setpoint gets reset back to what you want. This could be done with a separate program for each temperature and enabled for which is desired, if not v5.x You would have to watch out for your Else section, and not use it. If ....stat.temp is NOT $setpoint Then ....set it to the $setpoint again Else ....this is going to trigger after correction each time = avoid coding here. Now Then section (correcting it) will run ONLY when the stat doesn't match the $setpoint variable.

You assume incorrectly AFAIC. Sometimes people, knowledgeable about you subject matter, just dont see your post. Most here would like to help you and I have never noticed any negatives from your nickname. This may jog more people to see it. Sent from my SGH-I257M using Tapatalk

Still full from October 9th. https://www.timeanddate.com/holidays/canada/thanksgiving-day