Brian H

I would seriously doubt it. To name one difference a quick look showed. The 2413S PLM uses a 19,200,N,8,1 Baud Rate. The ZBPLM uses 115,200,N,8,1 Baud Rate. The sample Docklight file you can download from the devices web page does show some of the standard PLM serial command strings but the baud rate is also incorrect for the standard 2413S PLM.

You may also want to open the Event Viewer on level 3 and see if the RemoteLinc Button message is received each time the button is pushed.

When the sensor input changes. The sensor LED indicator will go On or Off. If you use the N/O and C it should go On when the relay is activated. The 5 volt terminal should not be used. Just the sensor and ground.

The EZIO8SA uses a separate PLM to interface to the power line. The majority of the Smartenit {Simplehomenet} modules are built into a basic PLM they buy from Smartlabs and use their custom Daughter Card. No external PLM is needed for them to communicate with your ISY System.

74551 is the Garage Door Kit and uses the 2450 I/OLinc. We have seen some Insteon modules ship with test links and X10 addresses in them. You may want to factory reset the I/OLinc to remove any test data left in them when they shipped and restore its databese through the Administrative console. You did do all the linking through the Administrative Console and not using manual link button routines?

I would have little faith in a Factory reset doing anything. When mine got flaky. I unplugged it for 12 hours and it then worked for maybe 5 days then crashed again. Next time I tried it it was running for maybe an hour then the LED again went out. I would say. Get a new PLM. Appearing to run extra warm would also indicate something is failing and getting warmer than normal.

Are you using any X10 modules or Insteon modules with a X10 address added? I see an X10 P13 Off (11) entry in your log.

Thank you for verifying it is a 10K Thermistor.

I don't have one to verify. 1. My thoughts are more on the line of a Thermistor that changes resistance with temperature. Over a Thermocouple generating a voltage proportional to temperature. 3. The internal photos of the 2441TH and 2441ZTH on the FCC Database both show what looks like the same small Blue Sensor. https://apps.fcc.gov/oetcf/eas/reports/ ... Search.cfm Grantee is SBP Product Code is the remaining parts of the listed FCC ID. 2441T for the wired. 2441ZT for the wireless. In the details tab. Photos and test reports.

There is no Insteon module that directly outputs 12 volts DC. As pointed out an I/OLinc or one of the Smartenit modules with an output relay could be used.

The wireless thermostat does not send the remote sensors data to any other module. It is only displayed on its own display. This thread may give you some added information. viewtopic.php?f=26&t=9833

Beta 4.2.1 lists the 2845-222 cat 10, sub cat 11, in its drop down list. Are you seeing it still being reported as a TriggerLinc?

Did you then do a compare to see if they matched what your ISY information is? The 00.00.00.00.00.00.00.00 Is the first unused link memory address not used and is normal. A compare should show it as ignored when compared to the ISY Link Table for the EZIO2x4

12VAC on I1+ and I1-. Could damage the Optoisolator if you exceed its input emitters reverse voltage break down. Even it you don't exceed its reverse break down voltage. The processor in the EZIO2x4 is seeing a 60 cycle On, Off pulse.

There is information in this thread. viewtopic.php?f=25&t=12880&hilit=weatherbug Weatherbug changed things and the Zip Code no longer works.

You may find this interesting. I believe some have used the CT-800 current sensor to trigger an I/OLinc. http://cocoontech.com/forums/topic/1142 ... erfurnace/ I have a older revision SynchroLinc. I will add it to my ISY and see what options show up. I see the Options where given to you by LeeG so I will not post it again.

Is the PLM the older 2412S that can also power the ISY99i or the 2413S with external power supply for the ISY99i? I had a 2413S fail in two years three months. Three months after the two year warranty.

Due to running out of programming space in an ISY99i. 3.3.10 will be the last firmware avilable for it. If all your modules are working correctly. No you don't have to upgrade to an ISY994i but no new model Insteon modules will be properly supported. I believe the special ISY99i to ISY994i upgrade is still on the UDI sales page.

This is an unofficial list of many of the Insteon devices. Mostly from what users have provided and known issues maybe listed. http://www.madreporite.com/insteon/Inst ... e_list.htm

The ISY99i was working OK and then started going into Safe Mode? You may want to contact UDI Support directly. They are excellent and will even schedule an appointment to troubleshoot your PLM and ISY994i for problems remotely if need. If you have not found the UDI wiki it is just full of useful information. Like a full users manual and troubleshooting information. http://wiki.universal-devices.com/index ... =Main_Page

Click on the sensor listing in the device tree and there should be an Options Tab on the bottom right side of the modules properties screen.

I doubt you damaged the 2413S PLM. When you say Reset. Was it through the Administrative Console or a Factory Reset with the Set Button? Where you using the start linking method or the New Insteon Device choice in the Link Management drop down menu, to add module? The flashing LED may indicate it is in the Linking Mode that was not stopped before trying to do something else. There are lots of tutorials and information in the wiki. Like full users manuals and how to start up guides. http://wiki.universal-devices.com/index ... =Main_Page

When you replaced the PLM. Did you power down the old PLM and ISY99i? The detection of PLM is done when the ISY99i powers up. If it was not power cycled it will not see the new PLM. From what I have seen here. Power down both the PLM and ISY99ii Replace the PLM and power it up first so it is completely initialized. Then Power up the ISY99i. Then use the Restore Modem (PLM) choice in the files menu. To add the new PLMs ID to all the modules in the system,. If your old PLM was a 2412S supplying power to the ISY99i. The new 2413S will not supply the power and you have to use an external power supply.

I reinstalled my problem 2413S into my ISY994i setup. It went dead in a few days. This time I observed it with out any intervention at all. In the time period of two hours. It went On and Off three Times. It was On when. It sent out the commands from the ISY994i as scheduled. My old V1.0 2413S is now handling the ISY994i's duties for now. I am not going to blow another $79.99 plus shipping on a device with a reputation to fail in just over its two year warranty period.

If the PLM is less than two years old. You should be able to get a warranty replacement. Mine is two years and four months old and totally unreliable. Just dies LED Out. Then later in the day is 100% good again and the LED is On. With no power cycle or my intervention. So for now. I have a original hardware 1.0; 2413S doing its thing.