Brian H

Thanks for the excellent support as always.

I have a D-Link DI-604. FW 2.8.2 My router table says ISY99-HOME-AUTO. If I power cycled the router it then said unknown. If I did a power cycle of the ISY99i, Router, Computer and DSL Interface. It again said ISY99-HOME-AUTO.

I also have never seen an ApplianceLinc act as a controller. Must be real new as none of mine will do it.

From the Smarthome forums. The later KPLs have a improper load detection circuit and a continuous beep is what happens. If it senses an improper load. http://www.smarthome.com/forum/topic.as ... hichpage=1 See the message from mprimous in the above thread.

Thank you for the hands on tests of the moisture sensor results.

On the UDI sales page you can purchase the IR Hardware Module. That you install in the unit itself. Then in the Purchase Optional Modules function ISY. You can then purchase the IR support module for the program itself.

Thanks for the update. Sounds like it may have been the old PLM.

It could be a noise spike confusing the controller chip in the OutletLinc. I have what I call my module confuser load. An old style inductive ballast fluorescent under counter light. I can kill an older revision ApplianceLinc with it. Totally confuse it until it just goes deaf and refuses to work. Sometimes the LED goes full bright or off completely. Only way to correct it is a power removal for a total power up reset. Newer revisions can also on rare occasions be confused by the same test light.

When you replaced the PLM did you use the Restore Modem (PLM) choice in the files menu. To up data the new PLMs address in devices?

After it shuts down. It is unresponsive to any commands until the power is cycled to the OutletLinc?

Smarthome has a new water detector sensor that can be used as an accessory with the I/OLinc. I have not seen it in a kit, just as an added purchased item. http://www.smarthome.com/71940/Minotaur ... sor/p.aspx They also have a Freezer Failure, Refrigerator Failure and Freeze Detector modules from the same manufacturer.

Are any of the LEDs, other than the Green PWR LED, flashing or on steady? Can you get into the Administrative Screen? If so. Tools Diagnostics PLM Info/Status See what it indicates.

The 2413S Dual band PLM, is 1023 links. The later revision 2412S PLM was 2016 links, but >800 seemed to be a problem for many. Original 2412S PLM was 417 links. Tools Diagnostics Show PLM Table When the table is read. There is a count button on the test screen. Note: It seems that any X10 or Insteon traffic on the power line during the test. Messes the count up.

MEM and ERR flashing together is can't communicate with the router or computer if directly connected. http://www.universal-devices.com/mwiki/ ... Y.27s_LEDs A 512MB SD card maybe standard. I believe the latest firmware allows larger ones. Diagnostics on mine shows an even smaller one. Total 125 MB Reserved 31 MB Bad 0 B Free 86 MB

Tools Diagnostics Show PLM Info/Status It will give you the PLMs six digit ID, firmware version and connected. If you decide to get a 2413S it does not supply power to the ISY99i like the 2412S models do. Smarthome has a power supply option to add one. They also sell a 2412SR Refurbished but I personally would go for the 2413S with added supply. Mine seems faster than when I used a 2412S.

I had two power failures yesterday. That where long enough for my ISY99i to restart. Both times the error log showed a -5 Start entry. I forced a reboot this morning in Configuration Tab and it then also showed a -5 Start when the reboot was done.

Thanks for the added information. I am thinking my EBay search didn't find it as it was closed. Yes the photos and description are of an ISY99i. I am also curious as to why it would be called an ISY26 in your routers table. Glad to hear the 2412S was also in the package deal. You may want to look at the links Rand and I gave you. For more information. If you have a firewall. You may have to tell it your ISY99is address is trusted. I know my Zone Alarm must have its address added to the Trusted Zone.

Your router indicates ISY26-Home-Auto? Mine says ISY99-Home-Auto. You may want to verify the model you purchased. I just looked on EBay and only found ISY26s. Telnet can be disabled. Maybe the former owner turned it off. You may find information in the UDI wiki or the Full Users Manual http://www.universal-devices.com/mwiki/ ... =Main_Page http://www.universal-devices.com/docs/i ... rguide.pdf I believe a Factory Reset would clear everything out and turn telnet back on. Though you may want to wait for feedback from others to confirm this before you tried it. Did you get a 2412S or 2413S for the PLM that goes with the ISY26 or ISY99i?

MorningLinc was added with the beta 2.8.2 release. http://forum.universal-devices.com/viewtopic.php?t=5037

Just curious if you got the RS485 option? I finally found the pin outs for it and I like the fact you can get the option and RS232 and power are still on the normally used pins.

LeeG; There are some threads here on the >800 links in a 2412S missing things. Even though it can have >2000 links in it.

The new V2 revision is completely different than the 1.? units. Mine are 1.0 and 1.6. There are internal photos in the FCC database of the V2 units. After taking the V1.0 apart. Yes power supply is different. Old version power transformer. New version power line driven switching supply.

Computer power supplies are known problem makers. You may want to use a FilterLinc on the PCs power as a start. I have one on my APC BX1000 UPS and the PLM is in the pass through outlet of the FilterLinc. Checking the Access Points with their built in test function may also yield some added information.

You may have signal communications problems with the slow writing process. Have you tried a scene test in diagnostics? What version of firmware is in your PLM? Tools Diagnostics PLM Info/Status should give you the firmware revision.

On the UDI sales page there are upgrade options from an ISY26 to all the model ISY99i's. The ISY26 did not get power from the PLM and was always supplied with the external wall wart. In fact I have my ISY26's wall wart powering my ISY99i with 2413S Dual Band PLM.