SHM

I have 2 nearly identical Polisy systems running at separate locations on the same type of network. Running IoX 5.6.0 and PG3 3.1.20. I have noticed that on one system, when opening IoX launcher the finder immediately opens the WAN and LAN options for both sites. When I open IoX launcher on the other system, the finder opens very slowly and often only the LAN address for the second site is displayed. Refresh does not do anything and opening a saved finder file does display the other WAN/LAN addresses, but very slowly and only for that session. I use the same laptop to open IoX launcher and it has the latest Java. Any ideas?

Just lost all communication with Insteon devices. Have tried ISY and Polisy reboot with no luck. Running IoX 5.5.9 and PG3 3.1.20

I have not added any electronics recently

Have been running IoX 5.5.9 on PG3 with Z matter just fine. I noticed that one wall light, controlled by an Insteon 2476D V 5.4, would no longer communicate with IoX. Did a factory reset of the switch, but it wouldn't add back to ISY saying it could not determine insteon engine. So, because it is an older switch, I just purchased and installed a new 2477D switch. When I try to add it to the ISY, I get the same message. Any recommendations? All my other insteon switches work just fine.

On 1.0.24 for a couple of days now. Works nicely. No issues so far. Going forward, I would agree with the advantage of adding iBeacon support as this really expands automation possibilities

Thanks. Giving it a try now

Have been using Occupancy for some time, with mixed results. Currently have UD mobile iOS 1.0.21. Where can I get 1.0.22?

Done. Thanks

I have 2 separate polisy devices at 2 locations, each running 5.5.7. All works well. When I set up UD mobile favorite page for one polisy, it creates the same favorites (same nodes) when I switch to the second IoX account on Polisy #2. Is there any way to have separate favorite node pages for each IoX?

I'll try that

Yes, but the schlage still added to the network under the Zooz stick, but not with Z matter.

Light yes. It was always the latest firmware

I'm having the same problem with Polisy 5.5.5 with Z Matter board. My Bladwin lock (Z-wave Plus 500 series) adds fine but my older Schlage (Z wave 300 series doesn't add. Was thinking that the 700 series Z Matter cannot communicate with the series 300, but then before installing Z matter, I had a Zooz (700 series) on the Polisy and the Schlage added just fine.

Its a ZW/IR Pro so I think it has a 500 board.

Sorry, I meant to say that after migrating to IoX on Polisy, I had a Zooz stick for the polisy. After upgrading the stick to ZMatter, I can no longer add the older Schlage lock (wave 300) to the network. I thought the network speed setting in 5.5.5 might allow me to add this lock.

Yes, when I was still using the 994

I had a Zooz stick in my 994 then migrated to polisy with Zmatter

I tried different network speed settings for my 2016 vintage Schlage lock (not Z wave plus) as it will not add to the network, I assume this is because the wave card in the lock is the 300 series and Z matter cannot communicate with it. Setting the network speed faster or slower did not make a difference. My Baldwin lock is Z wave 500 series and Z matter sees it without problem. I was just hoping that changing the network speed setting would allow Z matter to communicate with the Schlage, but I guess not.

Just upgraded successfully to 5.5.5. What z wave speed setting is recommended for Z-wave plus door locks and earlier version Z wave locks (e.g., schlage or baldwin)

Thanks very much!

I am on IoX 5.5.4 and PG3. Just noticed that 3 of my programs do not load because of "out of memory" Is this possible? I have 45 programs and 12 are not enabled.

I had the same problem with PG3 not seeing ISY on local network. Rebooted several times and seems to have resolved. But, the 5.5.4 upgrade wiped out all of my Z wave devices and had to start all over adding them back. Still cannot get Matter to see my Enbrighten switches

So I tried your recommendation and entered a geofence (with URL) for me an my wife's iPhone in ISY Occupancy. Used Locative to enter the appropriate URL for each person as a GET command. Both nodes (mine and my wife's) show up in the ISY, but only my geofence is updated by Locative. Have re-checked all URL data and nothing seems to be wrong. Not sure why my ISY node is updated but not my wife's. Any ideas?

Thanks! I'll try

I am using the same portal (mine) and trying to add a second geofence for my wife (separate iPhone). Have tried everything but no luck, so I thought I would try to add her as a user to see if that made a difference. When I try that and add her email, it shows up as "unverified" and she has not received any message to verify it.