SHM

That worked! Thank you.

Reboot Plugin or IoX?

Just finished upgrade from Polisy to Eisy. In the process, I had to re-install my plugins and I also upgraded the ESP Home firmware for my Ratgdo garage door openers. On the UDM side, I had to re-install my favorites and noticed that the garage door nodes not display the "open" of "closed" status, only integers ("0" for closed, "1" or "2 " for open), but the nodes open and close the garage doors normally. Not a big deal but not sure how to fix.

Thank you. I tried that but ended up re-installing and re-configuring each plugin

Just migrated from Polisy to Eisy. All went well, but Plugins dashboard shows all of my plugins are "unmanaged" and no response to "details" button. I have deleted the old polisy on portal, cleared java cache, re-booted but no effect.

I am planning on upgrading my old Polisy Pro (running PG3X 3.3.18, IoX 5.9.1 with internal ZWave/Zmatter card installed) to a new EISY. The migration instructions are a bit confusing. When I open the ZWave menu in the AC, there is no submenu selection for migration. So, do I make a backup of the ZWave network on the Polisy, then remove the card from the polisy and install in the EISY, then add the EISY to the AC and restore the ZWave network?

Anyone have experience with this new Aeotec z wave usb dongle on a Polisy? Specs show incredible range

I see. Thanks. Works perfectly.

Hmmm. I looked at the ISY manual but it's not clear. I am using integer variables. in a program, I assign an integer variable (X) the result of a sensor temperature outside the house. In the same program, I assign a second variable (Y) the result of a temperature inside the house from a separate sensor (thermostat). What I want to do is get the difference between the 2 variables (Y -X) and assign that to a third integer variable (Z). Then, if the difference is greater than 15 degrees F, the program turns the furnace on.

How do I perform simple arithmetic on several integer variables with the result assigned to a new variable? For example: $TempGradient = $inside temp - $ outside temp

I have been using Ratgdo and the plugin for several years. Flawless. Highly recommend.

Thanks very much

The previous version is not showing in my purchases, only the EVStream and the beta version. Any suggestions? Also, I still have the "Auth for Tesla" app. Is that still needed or helpful?

Hmmm My car is 2017, but the firmware is v12 (2025.14.1). If this is not compatible with the plugin, is there a way to reload the prior version of the plugin which worked well?

Here is the log after the plugin was open for 90 min or so. Still no changes in the data fields. TeslaEVpwrSh_4-24-2025_15747_PM.zip

Just did this. Just after re-start, I lost all nodes on plugin. Re-did test on AC which connected successfully, but had to run authenticate again to see nodes in plugin. Still no data. TeslaEVpwrSh_4-24-2025_71843_AM.zip

Still no joy. Test connection successful but no data from car. TeslaEVpwrSh_4-23-2025_91049_PM.zip

Yes, I have confirmed at my.isy.io that the remote connection is active. Hitting the test button results in "failed" TeslaEVpwrSh_4-23-2025_91509_AM.zip

So I have the short poll set at 3700 and long poll at 43200 but still get the 429 error

Pushed the test button and attaching the pre and post results. Nothing seems to have changed. New log attached. TeslaEVpwrSh_4-22-2025_44757_PM.zip

Thanks!!

Here are the latest screenshots. Not much has changed.

Makes sense. I have the free “hobby” subscription so any recommendations on the polling settings?

I get the same result TeslaEVpwrSh_4-21-2025_82722_PM.zip

Yes, I did run the authenticate and it logged me in to my Tesla account. Nothing happens when I hit the test button. Here is the log. TeslaEVstream_4-21-2025_65041_PM.zip