andrew77

To top it all off the set tab just broke New KPL time. Drew

Still no bueno When i do the restore it only controls the load (and not with the ramp rate it should have) I will then airgap it and then it becomes non responsive I'm going to delete it and rediscover it and probably just reprogram it. Don't know why this isn't working. Drew

Hi Teken I can turn the load off locally I can also turn the load on and off from the GUI I believe the KPL has been reset to factory So now I'm going to select the KPL from the GUI and restore? Drew

Hi Guys; I had this issue before. (Here's the link) http://forum.universal-devices.com/topic/16142-kpl-odd-behaviour-after-power-failure/ I've done all the steps outlined and I'm still having no luck. I've upgraded to Yosemite and I've downloaded the Java update. I can remove the KPL from the ISY and rediscover it I then try to restore it. This seems to do nothing. I've gone and airgapped the KPL but no luck getting my programs and scenes back in. I can just start again if need be but I'd like to work through this Thanks, Drew

Can I use a KPL button to trigger a non dimming item such as LED spotlights (non dimming) and the Insteon 2635-222 ON/OFF Module? I know the KPL buttons dim or brighten when you hold them pressed so I'm unclear if this is possible Drew

At least I'm not alone hahaha Thanks again. Drew

Thank you Brian Peace will now reside in my home once again. I'm assuming you meant can't in your reply not can' ? Drew

Hi guys; JUst a quick question. I was able to uncheck the box that stopped the remotelinc two from beeping. I was wondering if there was a way to do this with the remotelinc (original black ones)? I ask because my chocolate lab fears everything and the latest threat to her life in her opinion is that beep. Drew

I'm unsure how to manually run the THEN and ELSE paths. When I watch the ISY it seems to sometimes state that the program is on, other times, not. I found that the LED would turn on, then off, then on, then off again (not flickering or flashing like when its sending a signal but not receiving) I took out the 1 second delay and all the lights except two so I could test it easier than having to run around the basement. It now seems to choose when to work. Clearly I've made a mess of what seems to be simple.(?) Drew

Adding the 'else' line seemed to not work. It seems like such a simple program. If Status 'Hutch Lamplink' is Off Then Set Scene 'LED OFF Scenes / Hutch LED ON' Off Else Set Scene 'LED OFF Scenes / Hutch LED ON' On But sometimes I'll walk into the room where the hutch is and see the LED on and the hutch light off (or visa versa) I did it for these programs too. If Status 'Andrew's Office A' is not Off Or Status 'Basement Hall' is not Off Or Status 'Basement KPL A' is not Off Or Status 'Christmas Tree' is not Off Or Status 'Lamp Left' is not Off Or Status 'Lamp Right' is not Off Or Status 'Library' is not Off Or Status 'Theatre Room' is not Off Or Status 'Marion's Office' is not Off Then Wait 1 second Set Scene 'LED OFF Scenes / BASEMENT LED OFF' On Else - No Actions - (To add one, press 'Action') and the opposite If Status 'Andrew's Office A' is Off Or Status 'Basement Hall' is Off Or Status 'Basement KPL A' is Off Or Status 'Christmas Tree' is Off Or Status 'Lamp Left' is Off Or Status 'Lamp Right' is Off Or Status 'Library' is Off Or Status 'Theatre Room' is Off Or Status 'Marion's Office' is Off Then Wait 1 second Set Scene 'LED OFF Scenes / BASEMENT LED OFF' Off Else - No Actions - (To add one, press 'Action') but I find that sometimes the LED doesnt properly show the state of the light(s) Drew

Using the "else" part of it? If Status 'Hutch Lamplink' is not Off Then Set Scene 'LED OFF Scenes / Hutch LED ON' On Else Set Scene 'LED OFF Scenes / Hutch LED ON' Off Drew

Hi stillen_i30; I have (through the help of a few members here) two programs that I run to sync the KPL button LED to the status of the light. First I have a scene that only has the KPL LED button in it as a responder. Then I have these two programs. If Status 'Hutch Lamplink' is Off Then Set Scene 'LED OFF Scenes / Hutch LED ON' Off Else - No Actions - (To add one, press 'Action') If Status 'Hutch Lamplink' is not Off Then Set Scene 'LED OFF Scenes / Hutch LED ON' On Else - No Actions - (To add one, press 'Action') As an aside, if there's an easier way to do it I'm open to hear it. I hope this helps. Drew

I'm not sure if this helps but I have a hutch that used to have the type of control where you touch the designated hinge and the lighting inside would turn on 33%, next touch 66%, next touch 100%, next touch off. I opened the control box and hardwired it (solder, heated shrink wrap, etc…) and plugged it directly into a lamplinc. It's now controlled by a KPL button. (P.S. had an electrician friend eyeball my frankenstein job to make sure I didn't do anything wrong.)

oberkc, everything you suggested works. My problem was the PLM replacement. I'm finding out I have to restore my devices. Please forgive my ignorance on this. I've never replaced the PLM before and didnt know I would have to restore devices. I will back away from the forum slowly, ashamed, and try restoring before I bring an issue to the table. Drew

Hi oberkc; When I saw the failures in the tests I thought that too. I just got home from work so I'm futzing with it now. I just replaced the PLM a few weeks ago and had to 'restore' a SWL. I'm in the process of restoring the KPL now in hopes that thats the issue. I used to get awful comm errors constantly. I worked through all of them and nailed it down to a poor power supply in an old PC that's no longer in use. I havent had comm issues again until a month ago when the PLM failed. After I replaced it everything is rock solid again. I'll see if 'restoring' it works and if not I'll check out the questions in your posting. Drew

Hi oberkc; Thanks for getting back to me with this. Hopefully this summary points to where I'm going wrong. I only have the one KPL G button involved in this issue The basement off scene is a scene that shuts all the lights off, where as the basement LED off scene is the scene that only has the KPL G button as a responder. (this is the scene that is triggered by the programs mentioned in this post that I was hoping would set the status of the KPL LED, i.e. if any light is on the LED is on, if all lights are off, the LED is off) Yes, the controller is also a responder. I just have the one scene. Correct this is the basement LED OFF scene test Wed 11/27/2013 11:52:17 AM : [GRP-RX ] 02 61 30 13 00 06 ----- BASEMENT LED OFF Test Results ----- [Failed] Hallway KPL G Basement Dim (12 39 BB 7) ----- BASEMENT LED OFF Test Results ----- Wed 11/27/2013 11:52:25 AM : [iNST-TX-I1 ] 02 62 00 00 30 CF 13 00 Wed 11/27/2013 11:52:25 AM : [iNST-ACK ] 02 62 00.00.30 CF 13 00 06 LTOFFRR(00) This is the basement dim test Wed 11/27/2013 11:50:36 AM : [GRP-RX ] 02 61 1F 13 00 06 ----- Basement Dim Test Results ----- [Failed] Theatre Room (1D D4 B7 1) [Failed] Basement KPL D (18 58 67 4) [ignore] Andrew's Remote D (1C 34 4E 3) [Failed] Lamp Right (23 76 16 1) [Failed] Hallway KPL G Basement Dim (12 39 BB 7) [Failed] Christmas Tree (E A7 D5 1) [Failed] Basement Hall (18 B C7 1) [ignore] B Remote D Base Dim (14 37 10 4) [Failed] Lamp Left (23 74 29 1) [Failed] Andrew's Office D (A AE 5C 4) [Failed] Library (18 10 4 1) ----- Basement Dim Test Results ----- Wed 11/27/2013 11:50:41 AM : [iNST-ACK ] 02 62 00.00.1F CF 13 00 06 LTOFFRR(00) Wed 11/27/2013 11:50:41 AM : [Ext MH ] Unexpected Ack imCmd=62 cmd1=LTOFFRR 0x13 Wed 11/27/2013 11:50:46 AM : [iNST-TX-I2 ] 02 62 1C 34 4E 1F 2F 00 00 02 0E AF 08 62 03 0E A7 E3 FF 00 03 0B Wed 11/27/2013 11:50:46 AM : [iNST-ACK ] 02 62 1C.34.4E 1F 2F 00 00 02 0E AF 08 62 03 0E A7 E3 FF 00 03 0B 06 (00) Wed 11/27/2013 11:50:55 AM : [iNST-TX-I2 ] 02 62 1C 34 4E 1F 2F 00 00 02 0E AF 08 62 03 0E A7 E3 FF 00 03 0B Wed 11/27/2013 11:50:55 AM : [iNST-ACK ] 02 62 1C.34.4E 1F 2F 00 00 02 0E AF 08 62 03 0E A7 E3 FF 00 03 0B 06 (00) Wed 11/27/2013 11:50:59 AM : [1C 34 4E 1 ] Link 42 : 0EA8 [62030EA7E3FF0003] *Failed Writing [62..............] Wed 11/27/2013 11:50:59 AM : [ 1C 34 4E 1] ERR 1 I'm not sure how to manually execute the THEN path. That being said, if I try to manually trigger the basement LED scene from the ISY it doesn't light. (I've made exact copies of the scene but switched to different KPLs and they work fine. I've tried switching a different LED on the KPL in question and it doesn't work. I've tried air gapping the KPL. I'm getting no comm errors from it) If I have to start from scratch I'm not opposed to that. Drew

Hi Oberkc; The KPL G is controller in the 'Basement Dim' scene Its a responder to the All Off scene (just a whole house off scene) and the Basement Dim scene And my Basement LED OFF scene (the LED scene I created to try to control the status of the LED itself) This scene has only the KPL G LED at 100%. It also triggers this program If Status 'Hallway KPL G Basement Dim' is Off Then Set Scene 'Basement Off' Off Else - No Actions - (To add one, press 'Action') and of course the program in question. If Status 'Andrew's Office A' is not Off Or Status 'Basement Hall' is not Off Or Status 'Basement KPL A' is not Off Or Status 'Christmas Tree' is not Off Or Status 'Lamp Left' is not Off Or Status 'Lamp Right' is not Off Or Status 'Library' is not Off Or Status 'Theatre Room' is not Off Then Wait 1 second Set Scene 'LED OFF Scenes / BASEMENT LED OFF' On Else - No Actions - (To add one, press 'Action') If its a case where I have too much stuff on the one LED I can be good with that. I believe this works perfectly. If Status 'Barn Spots' is not Off Then Wait 3 minutes Set 'Barn Spots' Off Set Scene 'LED OFF Scenes / Spots off' Off Else - No Actions - (To add one, press 'Action') Its an entirely different KPL.

So, to recap. I have a KPL Button (G) that turns a basement scene on. (This works fine) When it is turned off, it triggers a program to shut off ALL lights in the basement, regardless if they are in the scene or not. (This works fine) Where it falls apart is this. IF there's any light on in the basement I want the KPL G Button to be lit. (This eludes me somehow) If Status 'Andrew's Office A' is not Off Or Status 'Basement Hall' is not Off Or Status 'Basement KPL A' is not Off Or Status 'Christmas Tree' is not Off Or Status 'Lamp Left' is not Off Or Status 'Lamp Right' is not Off Or Status 'Library' is not Off Or Status 'Theatre Room' is not Off Then Wait 1 second Set Scene 'LED OFF Scenes / BASEMENT LED OFF' On Else - No Actions - (To add one, press 'Action') I'm pretty sure at this point Insteon has recreated the Bugs Bunny "Boxing Glove On A Spring" with my name on it. I have been over the "Light the KPL LED Status thing with many KPLs and I can never get it to work 100% Sometimes it will seem to be correct but at one point I'll notice the LED is off when the light is on (or the other way around) Any help before I kick the chair out from under me would be greatly appreciated. (knowing my luck, the chair would trigger a scene and in my final breath I would notice the LED was incorrectly showing the status) Drew

Does it matter that the same KPL button triggers the basement scene on AND triggers a scene that shuts all basement lights off, regardless if they're in the basement scene or not? I'm hoping to just have the one KPL button be the basement button. Drew

Thank again. I've been trying this viewtopic.php?f=26&t=532 as well. The two are the same. My issue is I'll have an LED behave properly (or so I'll think) and then I'll notice the light on from some scene, etc… and the LED will not show the status properly. I'm ashamed to say I've been trying to figure this out (on and off) since I got into the ISY (back when the ISY-26 was around) Drew

I restored the device and it seems to work fine now. Thank you oberkc. I found that a few oddities (nothing major) were happening after the PLM switch. Things like kitchen lights turning on when a basement scene was triggered. And of course all the lights turning on at 5:30 AM (I have a nightscene that is shut off with a program that turns everything off at 5:30, the values on some lights were set to 100%) I don't have any lights set to 100% so I assume it defaulted on a few setting, etc… I'm still trying to figure out the LED status issue. viewtopic.php?f=27&t=12705 before I go bald (er) Drew

Hi Oberkc; The wait was me seeing if there was too much traffic. I should take it out. I tried to turn on the scene from the ISY and it didnt light up the LED. Have I done something wrong? I did notice it was in a mutually exclusive grouping and I've removed it. Drew

Hi Oberkc; Just did. The ISY says the SWL is at 50% (the setting it should be at) but the light is not. I just tried a scene where the SWL should be on and it is not, even though the ISY says it is. I've just replaced my PLM a week ago. Do you think it has something to do with that? Do you think it doesnt recognize it? I've had no problem with it until now. Drew

If Status 'Andrew's Office A' is not Off Or Status 'Basement Hall' is not Off Or Status 'Basement KPL A' is not Off Or Status 'Christmas Tree' is not Off Or Status 'Lamp Left' is not Off Or Status 'Lamp Right' is not Off Or Status 'Library' is not Off Or Status 'Theatre Room' is not Off Then Wait 3 seconds Set Scene 'LED OFF Scenes / BASEMENT LED OFF' On Else - No Actions - (To add one, press 'Action') I've tried this as well but it doesnt seem to work. I do have to admit I have a tough time trying to get the LEDs to properly display the status of a device For example, viewtopic.php?f=27&t=12705 viewtopic.php?f=26&t=532 Every once in a while I get the energy to try to get to the bottom of the LED status thing, after hours or days of running up and down a flight of stairs with a hopeful look on my face I eventually quit, cry in the front of the ISY GUI a little bit and then flog myself repeatedly for not getting the logic behind this. I don't want to post the same question over and over again and I don't want to burn out everyone's patience but I'd love to get my system working great. Drew

Hi Guys; I have a program that I've been working on. If Control 'A Remote 1 TV / Remotelink B Movies' is switched On And $Int_1 < 2 Then Set Scene 'Movies Brighter' Off Set Scene 'Movies' On $Int_1 = 2 Else Set Scene 'Movies' Off Set Scene 'Movies Brighter' On $Int_1 = 1 Seems to work fine but a SWL in one of the scenes doesnt turn on or off. (I've checked the scenes and the setting for the SWL are correct) When I press the remotelinc button the ISY GUI says the light is on at the proper level but in reality it is not on at all. Drew