andrew77

When I click it (non toggle off) it flashes once. None of the devices react Larry: No I haven't. I could try that. (pull the tab out for 10 seconds then push and hold all the way in for 10 seconds, correct?)

There are 26 separate devices in the scene I don't have the controller in the scene. The KPL triggers the scene via a program. (I have all the KPL buttons of each KPL in the scene as well to shut off, maybe that's an issue?) I've not gotten to see if the timer to shut it off works as I can't get the program to trigger first. The KPL that triggers the program is not in the scene This seems like it should be easier than this.

Bedtime Button - [iD 0008][Parent 0043] If Control 'Entryway KPL 7 Nighttime' is switched Off Then Set Scene 'Nighttime' On Else - No Actions - (To add one, press 'Action') and this is the Off timer Bedtime Button Off - [iD 0009][Parent 0043] If Time is 5:30:00AM Then Set Scene 'Nighttime' Off Else - No Actions - (To add one, press 'Action') For some reason when i push the Nighttime KPL button (set to non toggle off) nothing happens Drew

Hi guys; I had this scene/program working perfectly but since redoing my ISY I can't seem to get it back. I'm following all my steps in this post http://forum.universal-devices.com/topic/1110-night-scene/ but to no avail. In short, I want to press one KPL button (in non toggle off mode) this will shut off everything but leave four lights on at 20% Then at sunrise have a program shut everything off. It seems simple but then again so am I as it turns out. Any light on the subject (I didn't mean to do that, apologizes) would be great. Drew

Thank you Larry. Its been so long since I've had to tweak or fix anything as far as the ISY is concerned I've forgotten. Still not quite up to 100% so I'm sure I'll be posting more questions over the course of the day. Thanks again, Drew

Is the best way to have the LED of a KPL show the true status of a scene to make a scene with the KPL button in question and have it trigger when a program runs? Or is there an easier way to do this? I'd like the KPL button LED to reflect the status of the scene. (If I trigger a scene by double clicking a SWL and that scene is also triggered by a KPL button I'd like the KPL button to light.) I hope I'm making sense. Drew

Hi guys; I had my PLM go down and had to replace it. I've redone everything but I notice a few things are still hanging around from the original PLM/ISY programming. With two SWLs, I press on (up) and they only go to a certain on level and stop. I don't have them programmed to do this so I'm not sure how to make them stop. Also When I press the B button on a KPL the A button comes on as well. (I had this programmed like this before so this isn't much of a mystery except I thought by redoing everything this should have been erased.) Any thoughts? Drew

Hi Guys; I have to remotelinc 1's and a remotelinc 2 (the remotelinc two never worked consistently until I recently gave up and took it apart, now works great, clearly the evil gremlin has been let loose) Aside from that, one of the remotelinc 1's will kill batteries while the other one has lasted for months (maybe well over a year) I know a lot of people had this issue and was wondering if they've solved it or found a workaround. Drew

Hi guys; I have an older Lamplinc 2456D3 and was wanting to get another one but I can't seem to find it on the smart home site. I see a few 2 prong models but nothing with a ground pin. Am i looking in the wrong spot? Drew

I believe its the first Insteon device i purchased much longer than two years ago but I didn't know about the 2 year RMA Good to know for the future

To top it all off the set tab just broke New KPL time. Drew

Still no bueno When i do the restore it only controls the load (and not with the ramp rate it should have) I will then airgap it and then it becomes non responsive I'm going to delete it and rediscover it and probably just reprogram it. Don't know why this isn't working. Drew

Hi Teken I can turn the load off locally I can also turn the load on and off from the GUI I believe the KPL has been reset to factory So now I'm going to select the KPL from the GUI and restore? Drew

Hi Guys; I had this issue before. (Here's the link) http://forum.universal-devices.com/topic/16142-kpl-odd-behaviour-after-power-failure/ I've done all the steps outlined and I'm still having no luck. I've upgraded to Yosemite and I've downloaded the Java update. I can remove the KPL from the ISY and rediscover it I then try to restore it. This seems to do nothing. I've gone and airgapped the KPL but no luck getting my programs and scenes back in. I can just start again if need be but I'd like to work through this Thanks, Drew

Can I use a KPL button to trigger a non dimming item such as LED spotlights (non dimming) and the Insteon 2635-222 ON/OFF Module? I know the KPL buttons dim or brighten when you hold them pressed so I'm unclear if this is possible Drew

At least I'm not alone hahaha Thanks again. Drew

Thank you Brian Peace will now reside in my home once again. I'm assuming you meant can't in your reply not can' ? Drew

Hi guys; JUst a quick question. I was able to uncheck the box that stopped the remotelinc two from beeping. I was wondering if there was a way to do this with the remotelinc (original black ones)? I ask because my chocolate lab fears everything and the latest threat to her life in her opinion is that beep. Drew

I'm unsure how to manually run the THEN and ELSE paths. When I watch the ISY it seems to sometimes state that the program is on, other times, not. I found that the LED would turn on, then off, then on, then off again (not flickering or flashing like when its sending a signal but not receiving) I took out the 1 second delay and all the lights except two so I could test it easier than having to run around the basement. It now seems to choose when to work. Clearly I've made a mess of what seems to be simple.(?) Drew

Adding the 'else' line seemed to not work. It seems like such a simple program. If Status 'Hutch Lamplink' is Off Then Set Scene 'LED OFF Scenes / Hutch LED ON' Off Else Set Scene 'LED OFF Scenes / Hutch LED ON' On But sometimes I'll walk into the room where the hutch is and see the LED on and the hutch light off (or visa versa) I did it for these programs too. If Status 'Andrew's Office A' is not Off Or Status 'Basement Hall' is not Off Or Status 'Basement KPL A' is not Off Or Status 'Christmas Tree' is not Off Or Status 'Lamp Left' is not Off Or Status 'Lamp Right' is not Off Or Status 'Library' is not Off Or Status 'Theatre Room' is not Off Or Status 'Marion's Office' is not Off Then Wait 1 second Set Scene 'LED OFF Scenes / BASEMENT LED OFF' On Else - No Actions - (To add one, press 'Action') and the opposite If Status 'Andrew's Office A' is Off Or Status 'Basement Hall' is Off Or Status 'Basement KPL A' is Off Or Status 'Christmas Tree' is Off Or Status 'Lamp Left' is Off Or Status 'Lamp Right' is Off Or Status 'Library' is Off Or Status 'Theatre Room' is Off Or Status 'Marion's Office' is Off Then Wait 1 second Set Scene 'LED OFF Scenes / BASEMENT LED OFF' Off Else - No Actions - (To add one, press 'Action') but I find that sometimes the LED doesnt properly show the state of the light(s) Drew

Using the "else" part of it? If Status 'Hutch Lamplink' is not Off Then Set Scene 'LED OFF Scenes / Hutch LED ON' On Else Set Scene 'LED OFF Scenes / Hutch LED ON' Off Drew

Hi stillen_i30; I have (through the help of a few members here) two programs that I run to sync the KPL button LED to the status of the light. First I have a scene that only has the KPL LED button in it as a responder. Then I have these two programs. If Status 'Hutch Lamplink' is Off Then Set Scene 'LED OFF Scenes / Hutch LED ON' Off Else - No Actions - (To add one, press 'Action') If Status 'Hutch Lamplink' is not Off Then Set Scene 'LED OFF Scenes / Hutch LED ON' On Else - No Actions - (To add one, press 'Action') As an aside, if there's an easier way to do it I'm open to hear it. I hope this helps. Drew

I'm not sure if this helps but I have a hutch that used to have the type of control where you touch the designated hinge and the lighting inside would turn on 33%, next touch 66%, next touch 100%, next touch off. I opened the control box and hardwired it (solder, heated shrink wrap, etc…) and plugged it directly into a lamplinc. It's now controlled by a KPL button. (P.S. had an electrician friend eyeball my frankenstein job to make sure I didn't do anything wrong.)

oberkc, everything you suggested works. My problem was the PLM replacement. I'm finding out I have to restore my devices. Please forgive my ignorance on this. I've never replaced the PLM before and didnt know I would have to restore devices. I will back away from the forum slowly, ashamed, and try restoring before I bring an issue to the table. Drew

Hi oberkc; When I saw the failures in the tests I thought that too. I just got home from work so I'm futzing with it now. I just replaced the PLM a few weeks ago and had to 'restore' a SWL. I'm in the process of restoring the KPL now in hopes that thats the issue. I used to get awful comm errors constantly. I worked through all of them and nailed it down to a poor power supply in an old PC that's no longer in use. I havent had comm issues again until a month ago when the PLM failed. After I replaced it everything is rock solid again. I'll see if 'restoring' it works and if not I'll check out the questions in your posting. Drew