Blackbird

Seems to work good. Thanks

I should also add that both failed while turning it on using mobilinc. Not sure if that matters.

I have had 2 2663-2 wall outlets fail. I had my wall air conditioner plugged into it and it worked for a couple months then smelt a burning smell and it doesn't work anymore. The air conditioner is 11.5amps and the outlet says 15 amp

If you say "run if" does that run the whole program or just the "if" section of the program?

I think my previous thread was deleted but I have these two programs running to let me know if I left my door open and it works fine. Garage Man Door left open - [iD 0054][Parent 0050] If Status 'Garage Small Door-Opened' is On And Status 'Garage Small Door-Opened' is not Off Then Wait 2 minutes Send Notification to 'email' content 'Garage man door left open' Send Notification to 'Pushover' content 'Garage man door left open' Enable Program 'Garage Man Door repeat ' Run Program 'Garage Man Door repeat ' (Then Path) Else Disable Program 'Garage Man Door repeat ' Garage Man Door repeat - [iD 0058][Parent 0050] If - No Conditions - (To add one, press 'Schedule' or 'Condition') Then Repeat Every 30 seconds Send Notification to 'email' content 'Garage man door left open' Send Notification to 'Pushover' content 'Garage man door left open' Else - No Actions - (To add one, press 'Action') I want to use this program to disable the above programs for 20 minutes then re enable them and this does the trick. Disable Garage doors left open - [iD 005C][Parent 005B] If - No Conditions - (To add one, press 'Schedule' or 'Condition') Then Disable Program 'Garage Man Door left open ' Disable Program 'Garage Man Door repeat ' Disable Program 'Overhead Garage door left open' Disable Program 'Overhead Garage Door repeat' Wait 20 minutes Enable Program 'Overhead Garage Door repeat' Enable Program 'Overhead Garage door left open' Enable Program 'Garage Man Door repeat ' Enable Program 'Garage Man Door left open ' Else - No Actions - (To add one, press 'Action') The problem is after the 20 minutes are up, it re enables the "garage man door left open" program but if the door was still open at the time, it doesn't notify me again. How do I make it check if the door is open or not? Thanks

Can you be more specific on the devices or relay required?

I really want to incorporate a sensor like the driveway sensor into the ISY so I can get email alerts.

The fact that I didn't understand most of what you wrote, tells me it might be beyond my skill

I'm not sure of the brand, I believe it is a chamberlain. It is an extra set of photosensors I have and unrelated to my garage door. Just thought it would be a cheap idea to use it to detect people walking into my pathway.

I want to use a set of electric photo sensors that come with a garage door opener and connect it to the iolinc so if anyone passes through the beam it will send an alert. Is this possible and how would I wire it? Thanks

These are the instructions Kaspersky sent me on how to add your ip to the trusted sites. It now works fine. Thanks guys To add a website to the Trusted URLs list: Open Kaspersky. Click on 'Settings'. Click on 'Protection' on the left. Click on 'Web Ant-Virus' on the right. Click on 'Advanced Settings'. Click on 'Configure trusted web pages'. Click on the 'Add' button. Enter the web address in the same format as shown: http://*.example.com/* Select 'Active'. Click on the 'Add' button. If needed, repeat the process for additional sites. Close the 'Trusted web pages' window. Click the Back arrow in the upper left three times to return to the main window. Retry the web site. If it does not work, close all open web browsers and reopen the site.

Is the ip address found in the "about" in admin console?

That link suggests allowing Java complete access on Kaspersky. That doesn't sound like a good idea

Kaspersky was the problem Michel, you were on the right track. I'm guessing that Kaspersky (on both my computers) updated and it didn't agree with the ISY. So do make an exception for Java in Kaspersky?

I also tried a different Ethernet cable to the ISY and still same problem

New info! I just tried logging into the admin console from my HTPC but I have the same problem. I used to be able to log in before and nothings changed on that computer but now I cant.

I get the universal devices logo, then very briefly at the bottom windows says its running a security scan in the middle of the screen, admin console loads, asks for my login, I enter it, then for a brief second I see my ISY and then it closes.

Is that for the admin console or the firmware for the isy?

I'm using Kaspersky internet securities

1.8.0_73

I had to enter the admin password to install. I did login as admin and had the same results. I see my scenes for about 1 second then it closes

I downloaded and installed the 32 bit version. It is in my program 86 folder. But it still doesn't work. Only difference about this windows install besides windows 10 vs 8 is I am a user not an admin. Before I just ran my user name as an Admin

I'm not sure what you mean by which option to download admin console? I'm not sure of my firmware until I can get into the ISY to see

I don't see an option to install 32 bit only

did that and it still doesn't work. Admin console still wont load