jkraus

Interesting comment about the low battery. It did blink several times when button pressed like it had poor communication issue (so possibly low battery you say). However, upon restore, without any battery change, works again just fine. However, this is a unit that I just changed the batteries in a couple of weeks. I though it kind of odd because the batteries were not that old especially the unit is not used too much. I remember a thread about some RLs having problem with eating through batteries, maybe this is the issue. Does anyone know the ver of the bad battery devices? Thx Joe

Hi, just wanting to debug an issue I had with a RemoteLinc. Without any isy changes (program or firmware) one of my RemoteLincs stopped controlling the devices on any of the buttons. I did a restore on the Remotelinc from the isy and worked fine, but wondering how this could happen i.e. how did a RemoteLinc lose all of its lincs?

Thanks michel Yes I found this between my second and third post, so thanks for the help. I have no idea why installing a new certificate increases my security since log on is the same but I guess I need to do some reading Thx Joe

Ok now I see how when I get to the blank consol how to add a new certificate. So I did so but i have no idea what I did or what effect it has, sorry for the lack of knowledge in this area

thanks Mitchel I dont really understand the concept of certificates but I like to learn. In any case when I select "manage my certificates" form the admin Consol from local PC it goes to another admin consol and has me log in again so I do then the admin consol is blank. So I am at a loss of what to do next Joe

I have my isy port forwarded and using dyndns to give me a fixed ip for login remotely, and all works fine, I can logon securely (https at port 443) and unsecure at port 8o with http. However when I run either one from PC on my network just to try it when I go to the admin consol and log on it gives message to disble internet or get new certificate, neither one does anything. If I say get new certifcate it goes to another admin consol log on with nothing there, in either case if I just closebthe messge everything works fine. What is going on? and is it necessary to log on securely (https port 443) or not, as this is an are I am not expert on> Thx Joe

in my old cabin I used to use an X10 dial up reciever to turn on a X10 relay that was inline with the wire to my thermostat preset at 70 degrees. When I was leaving for the cabin I called ahead ond truned on the heat. Worked great! Is this still the best way in this insteon world or is there a better way? I hate to buy another isy just for the remote feathure.

thanks on the return info. yes load is only two 60 watt incandescents

Yes, absolutly ZERO ohms, new one works fine. Will SH repalce this as 1.5 ys old?

factory reset did not work. Interesting that I could do a restore form the isy with no problem so the Insteon logic is still intact, but no help, so I think your guess may be a good one. Is this a common failure mode do you know?

I used to use Logmein but now that is resticted

Thanks Brian On the chance that it is defective as you described I have ordered another one from SH, in the meantime I will try tonight a factory restore just to see Thx Joe

This morning my togglelinc dimmer did not turn off my garage lites. I though it missed a command , but when I went to physically toggle it off the the LED glowed (like it was in off position) but the lites stayed on. When I turned off and back on the circuit breaker that the TL was on they lights still stayed on. Is the TL gone bad or does a factory reset help? If I do a factory reset, then do a restore device from the isy? Do I have to remove the switch form any scenes BEFORE I do a factory reset?

ha, this would be useful. I have a lamplinc that I swear is removed, but isy says that it is linked and I can turn it on an off?? I would love to send it a peep to see if I can find it, as this is driving me nuts as I have looked in all my outlets. How do I beep it?

work firewall. Even Michel could not fix it.

sorry that commet about size was in differnt thread, not this one. Thanks, but yea need stadrad size and outdoor rated as for pool pump and the 2477 is not after talking to SH

seriously? do you mean 2477SA1, ? wont fit need a standard light fixture size and outdoor rated

OK, this is not high on my wish list, but often at work when I have a few minutes it would be great to try to interface with my isy, however, our firewall at work prohibits it (for sure as Michel has tried to fix), so I was wondering if there was a "dummy" admin console available where could at least see the programming interface at work to check out some syntax's. Does it exist?

adding to this , is there any X10V 220V switches that isy99 can read the status, as Insteon 220V do not conveniently fit in my current enclosure as would love to upgrade to Insteon but do not have a neutral at the switch

Brad77 thanks much, makes sense. However, for some reason I have a mental block about how to use programs as flags. I have tried before, but does not seem to sink in. It would seem to me that if a program is running it is true if not it is false, but it does not seem to work that way. is the only way to change a program status to True or False is by telling it to do so from another program? Any help you can give me would be appreciated, as I have not grasped this fully Thx Joe

ahh, that would work if it were Insteon, but alas it is my LAST x10 device, a 220V x10 switch

Hi, just purchased the Weather Bug Module to start my pool pump when it gets near freezing. To test it out first I wrote a program to just send a text alert when "Temp > 50F". Seem to work great as it rose above 50F this morning, but now I get alerts every few minutes. I am guessing that as long as it is above 50F it will keep sending me alerts (very annoying ) . So how do I set up the program to only send one alert because eventually I only want to turn on the pump once Joe

seems the first RL indeed is dead as I finally got the second RL to link by selecting "auto discovery" and all seems fine. only other comment is the 1st RL was quite sensiteive to a drop as X10 you can basically throw at the wall and still works

OK, here is one for all? Dropped my remotelinc on sidewalk and control stopped working. LEDs and beeps seemed normal but still would not control lights. Removed links from ISY and did a factory reset, but could not linc it. So figured it was dead. I have a brand new spare that I then tried to linc and it failes. Get error messgaes "failed writing higwater mark" and "node not added" wierd coincidence. any ideas?

you bring up some interesting difficulties. Let me ask a question, you may know. If I had a scene that was controlled by say 3 different keypads lets say all pad "A". when I hit any of the keypad "A" all three of the keypad button "A" lite. If then I make any adjustments to the lights in the scene, all three keypad "A" stay lit, until I turn one of them off. This I believe to all be true So if I were to use the status of the Keypad "A" (I think I can do that), would that be a reliable measure of the "scene being on" to be used in a program?