tlightne

Did you run a backup before migrating to Zmatter? From what I read in other posts you can restore a backup taken before the migration.

Upgraded to 5.5.5 could not get Zwave add or remove to start after hitting button. Pulled the plug on Polisy and after a reboot all seems to be ok now. I am still having issues with First Alert Smoke Detectors 1st (Not Zwave Plus) reports V1 Alarm Type as 13, V1 Alarm Level 255, When Smoke it detected it reports V1 Alarm Type as 1 and V1 Alarm Level 255. When hitting Test button on detector V1 Alarm type id 12 so it looks like it is reporting a Binary Alarm type. It does report Battery Level. Second First Alert Combo Smoke/CO Detector (Zwave Plus) does not report any status for CO Alarm, Co End of Life, Smoke Alarm, Test Alarm, and Smoke Detected all of which reported with Zoozs 700 Dongle. It does report Battery Level, System Alarm as Heartbeat, and its a wake status so it is communication with the Zmatter Board. After removing and readding the (9) KAIPULE Z-Wave Plus Wireless Door Window sensors I picked up a new node called Binary Door/Window Sensor, This reports On when Window/Door is opened and Off when closed. The Access Control node still reporthat when door is open it reports as Open in Polisy but when closed it repots Open when Window/Door is open but Idle when Window/Door is closed. As Chris reported did not have time to impliment the F/C fix this update so the two Philio PAT02-2B Zwave Plus sensors report in temperature as Celsius and the default is Fahrenheit. Awaiting the next code update.

@Chris JahnIs the glitch in the Build just PG3X or also PG3? I am holding off 5.5.5 until I hear back. Thank you

@bradshawkyle I am considering moving from a Nest to a Honeywell thermostat. What model Honeywell Home are you using? Thanks...

Just updating here my progress... Update: As of 01/29/2023 @ 13:51. All Original devices are now connected to the Zmatter Network. I had to uninstall the Eaton recepticle move it closer to the Polisy then it included in the Zmatter network. I am still having issues with First Alert Smoke Detectors 1st (Not Zwave Plus) reports V1 Alarm Type as 13, V1 Alarm Level 255, and does not report Battery Level. Second First Alert Combo Smoke/CO Detector (Zwave Plus) does not report any status for CO Alarm, Co End of Life, Smoke Alarm, Test Alarm, and Smoke Detected all of which reported with Zoozs 700 Dongle. It does report Battery Level, System Alarm as Heartbeat, and its a wake status so it is communication with the Zmatter Board. Both Smoke detectors have been in the Zmatter network for over 24 hours. The two Philio PAT02-2B Zwave Plus sensors report in temperature as Celsius and the default is Fahrenheit. Tried to change the configuration but it will not change. The (9) KAIPULE Z-Wave Plus Wireless Door Window sensors that when door is open it reports as Open in Polisy but when closed it reports as Idle not closed. I am hoping the next Firmware update will pickup and fix these.

@tazmanThanks for the update. I assumed someone already had a ticket opened but I thought the more the marrier....

I completed the migration to Zmatter yesterday.I few of my devices migrated with no issues however I have (9) KAIPULE Z-Wave Plus Wireless Door Window sensors that did not upgrade from the Zmatter install. I did an exclude and reinstall and the did show up. However when door is open it shows Open in Polisy but when closed it shows Idle not closed. I cannot get notified when the door or window is closed. I also have (2) Philio Zwave Plus Temperature and Humidity sensors and two First Alert Zwave Smoke detectors that will not include into the Zmater network. I see them go into the interview process but never get added. UPDATE: I also have 1 Eaton Zwave Plus outlet that I can not get included in the Zmatter network. I have excluded it both through the IOX and it also has a factory reset which excludes it from all settings. I have opened a ticket with UD support but thought I would put it out here as well.. Firmware is 5.5.4. Ploisy with Zmatter... Thank you

I have them listed in a program then statement. Right click the program and run Then...

Did you unplug the power and wait a few seconds then repower your Polisy?? Just doing a backup should not make your Polisy go offline..

@bpwwer stated earlier there are issues with eisy and Pg3 a new level of Pg3 should be out next week.

Thank you I guess I will try a delete and reinstall. I did a reinstall but did not change anything. Thanks again...

@bpwwerAmbient Weather Node Server is blank on my IOx (Polisy). It has been installed and running fine for several months. I did a reinstall this morning and it is still not updating on Polisy. I have restarted the Polisy, and restarted PG3 and still same problem. I have attached PG3 log and Ambient Node serverLog. AmbientWeather_12-15-2022_90145-AM.zip pg3_12-15-2022_90005-AM.zip

I would start with replacing the power supply. I had to replace mine last summer.

@bpwwer Just tried the restart and still shows version as 2.06 but like I said low priority for me...

I have the same issue but since everything was running ok it was low priority...

@Jimbo.Automates Got it Thank you....

@Jimbo.Automates There is no message after 144 but there is a blank section for a message. How do you delete messages in the configuration? I have figured out how to do short custom messages so I can get additional messages that way at least for now. Thank you

@Jimbo.AutomatesAttached is the log file. I am not really very good at programing so I found it easier just to add them to Custom Typed Configuration Parameters in the configuration in the node server. It lets me enter them in and save them they just will not show up in the IOP. Here is an example of my programs: Notification_11-9-2022_14918-PM.zip

When you look in the Admin Console you and click on the node server you should see Nxxx_zzzzzzzzz - Ambient Station xxx should be the Node server slot in IOP and ZZZZZZZ is the MAC address of your station. @bpwwerMine is working as designed. Just FYI....

@Jimbo.Automates Is there a limit on the number of messages that can be created in the controller node? I have 140 messages I have entered but when I enter more they do not show up in the IOP.. Thank you

I was seeing the Subscription 404 errors but all has been working as designed since yesterday afternoon. Thank you for all you do.....

If you do not have your own PWS you can load Open Weather node server and pull data from there.

I had same issue with UD Mobile and 404 errors. Have not seen any in a couple of hours.

It is my understanding ZW is strictly RF. The PLM is for Insteon powerline products.

@bpwwer Loaded PG3 3.1.12 this morning with no issues. Backup now working as designed.. Once again thank you far all you do...