3 hours ago, bmercier said:

eisy-ui plugins is no longer beta.

It is released to production under eisy-ui 1.4.4.

Thanks @bmercier , up dated and everything seems fine

Question, after every update I'm left with an error loading group and a reboot doesn't fix. Pulling the power is always required.

Is this expected behaviour?

4 hours ago, bmercier said:

eisy-ui plugins is no longer beta.

It is released to production under eisy-ui 1.4.4.

Migrated this morning. All seems good except I cannot migrate PG3 plug-ins. I've tried 4 and I get the same message on each "Error getting PG3 plugin config: Request failed with status code 503". Am I doing someting wrong?

Edited 23 hours ago23 hr by Mr B
Update: Opening a ticket

23 minutes ago, mmb said:

Thanks @bmercier , up dated and everything seems fine

Question, after every update I'm left with an error loading group and a reboot doesn't fix. Pulling the power is always required.

Is this expected behaviour?

Thanks for the tip, @mmb I had to unplug as well to get the plugins operational.

1 hour ago, Bumbershoot said:

Thanks for the tip, @mmb I had to unplug as well to get the plugins operational.

My brother has an almost identical setup as me except a much smaller set of devices. I do his Eisyui updates and see the same behavior on his.

Note: Plugins are unresponsive after the update and subsequent reboot from the Eisy. I checked services and IOX was not running, so started it. That didn't help so restarted the eisyui service, still nothing. Power reboot fixed everything.

Also note, my brother ran into a recent issue that couldn't be fixed so reflash was necessary. So the Eisy should be pretty close to factory except one update. He's a little gun shy about updating to these latest updates.

Let me know if you need any information @bmercier

@Jimbo.Automates When I migrated HomeKit and Ecobee, and then looked at the nodes, the HomeKit Hub nodes all looked normal. But the node for my Ecobee thermostat had an error message, instead of usual readouts & controls. I've not yet had a chance to see what happens if I migrate only one or the other of the two plugins.

All of my other plugins migrated successfully.

UPDATE: Appears to work well when migrating HomeKit, but leaving Ecobee on PG3

Edited 12 hours ago12 hr by BJB2757
New info

@bmercier What to do here? thanks.

Elk plug in is only finding Outputs...

See sample screenshot of log.

Any advice to fix? I have restarted it twice. Will reboot eisy to see if that fixes it.

2 hours ago, dbwarner5 said:

@bmercier What to do here? thanks.

I see an update may solve this.

2 hours ago, dbwarner5 said:

Elk plug in is only finding Outputs...

See sample screenshot of log.

Any advice to fix? I have restarted it twice. Will reboot eisy to see if that fixes it.

Migrated it back to PG3X.. all the nodes are showing in the dashboard of PGX3, but only the output nodes are showing in Eisy UI... Any ideas how to get them to show back up?

Edited 16 hours ago16 hr by dbwarner5

41 minutes ago, dbwarner5 said:

Migrated it back to PG3X.. all the nodes are showing in the dashboard of PGX3, but only the output nodes are showing in Eisy UI... Any ideas how to get them to show back up?

Solved:

Had to go to the AC and then Plugins / Add all nodes. They are back and working normally again.

I have tried unplugging / restart, and the Add All Nodes suggestion but still getting this error message. The eisy-ui PG3 (Legacy) page is populated with all Plugins connected.

Migrate All results in them all coming over with the same error.

Edited 4 hours ago4 hr by Phil G
clarity

There are new firmware updates just released that address the PG3 issues

Edited 3 hours ago3 hr by Techman

1 hour ago, Phil G said:

I have tried unplugging / restart, and the Add All Nodes suggestion but still getting this error message. The eisy-ui PG3 (Legacy) page is populated with all Plugins connected.

Migrate All results in them all coming over with the same error.

I tried the migrate all option and it was a semi-disaster.. eisy crashing, plugins "failed", wont start, etc.. I had to move them all back to PG3X, do a restore to my Eisy and then after getting everything restabilized, I moved them one at a time. That worked. Had trouble with iAuqalink, RATDGO and ELK, so kept them for now on PG3X. A few others with known issues I also did not move; Matter, St-inventory.

Installed the latest update but haven't tried to re-migrate those three yet as I rely on them too much to deal with this weekend.

1 hour ago, dbwarner5 said:

I tried the migrate all option and it was a semi-disaster.. eisy crashing, plugins "failed", wont start, etc.. I had to move them all back to PG3X, do a restore to my Eisy and then after getting everything restabilized, I moved them one at a time. That worked. Had trouble with iAuqalink, RATDGO and ELK, so kept them for now on PG3X. A few others with known issues I also did not move; Matter, St-inventory.

Installed the latest update but haven't tried to re-migrate those three yet as I rely on them too much to deal with this weekend.

@dbwarner5 , to be clear, you had to restore IoX from a backup? Did you do that in A/C or eisy-ui or does it even matter? Thanks for the tip.

1 hour ago, Techman said:

There are new firmware updates just released that address the PG3 issues

I did Upgrade Packages early this morning and then this trouble seemed to start. Not positive though because I only did the big upgrade to eisy-ui late yesterday and still not too familiar with it. You have to love how simple it is now to review package versions and perform upgrades. Boot Environment feature is pretty cool, too. Worth the pains to get to this point in my opinion. Well done, UDI.

On 10/15/2026 at 7:50 PM, Javi said:

If all plugins are migrated, disable pg3 in menu>settings.

Thanks @Javi , I disabled PG3 and did a followup check on EisyUI Services and PG3X is still running.

Are there legacy PG3 bits that are still needed requiring the service to continue to run?

My PG3 (Legacy) Dashboard randomly does this: