SHM

Here are the latest screenshots. Not much has changed.

Makes sense. I have the free “hobby” subscription so any recommendations on the polling settings?

I get the same result TeslaEVpwrSh_4-21-2025_82722_PM.zip

Yes, I did run the authenticate and it logged me in to my Tesla account. Nothing happens when I hit the test button. Here is the log. TeslaEVstream_4-21-2025_65041_PM.zip

Understood, but why would one plugin have an error and the other does not (given the polling settings are the same but the API's differ)?

OK. It is strange that only one policy gets the error and the Weatherbit plugins are set up on 2 separate accounts.

Thanks. Will give it a try.

Just upgraded to the new plugin. The plugin installs OK and I get the 2 nodes, but most of the data is missing in the fields. Any suggestions? TeslaEVstream_4-21-2025_100948_AM.zip

Added the Notification plugin and setup per "Notification for Dummies" When I open the AC and look at the emails/notifications.customizations section, I do not see the "UD Mobile Event Template." Any suggestions?

I have successfully installed the plugin on 2 separate Polisys, using 2 different Weatherbit API's (2 accounts). The data fields seem to populate OK but on 1 Polisy, I get a 429 error. Any suggestions?

OK, will try that. When I first tried step 7, the enable button was greyed out and, as you mention, I was unable to enable it later.

I have installed the plugin and followed the instructions for the Client ID, Client Secret, etc. Paid the $5.00. When I try to authenticate, I get API error. Evidently, my topic has not been enabled, and I can't seen to do that, so perhaps the plugin does not have access to the api? Attached is log and some screenshots. Also tried to update version 1.05 but nothing happens. NestSDM_3-10-2025_93938_PM.zip

Well, that was easy...

Sure. Here they are.

Have been running version 4.08 flawlessly. After some power outages recently (or maybe upgrade to 5.9.1?), the AC is showing only 1 node for my garage door (node007, "Online" and Remote Lock"). However, the plugin show both nodes, the second showing "Door State" and "Obstruction." Interestingly, the programs in the AC to open or close the door work fine. I have tried to re-boot the policy in the AC several times, with no effect. Should I delete/re-addm the plugin and re-discover?

Thank you!

I have a motion sensor that detects the presence of my car in the garage. The presence or absence (1 or 0) is saves in a state variable, $caringarage. When there is a power failure or any event that causes the Polisy to re-initialize, $caringarage is reset to 0. The ISY manual shows a way to preserve the state variable value, but the syntax is confusing. Any suggestions/examples?

Upgraded IoX to 5.9.1 without issue. When I open PG3x, not seeing the 14.1p6 version. Is this normal?

Thanks to both. I'm about 10 miles from the nearest airport in Seattle area , where my current NOAA plugin draws data. But, that data is often incomplete. for example, on a cloudy day I have program to leave some lights on in the house, but the NOAA "climate conditions" is infrequently populated.

Which is better in terms of weather for a specific location (lots of microclimates in my area) and data use in ISY programming: Openweathermap or Weatherbit?

Problem solved! I eliminated the "token" from the older node version and all works.

Yes. Have tried both with no effect

I have installed the new NS and installed in PG3 (latest firmware). Restarted the NS and ran authenticate, which took me to Tesla.com where I signed in (for my 2017 Model S). NS then returned 4 nodes: Charging info (with 20 sub nodes, most showing data), Climate info (17 sub nodes, most showing data), Tesla EV info (5 sub nodes) and Merrick Tesla (18 sub nodes, mose showing data). On the AC, only 2 nodes show up (see attached) with no data. Attaching the log and some screen shots. Not sure where to go from here. udiTeslaEV2_1-4-2025_12726_PM.zip

Will the new OS run on Polisy PG3X?

The first worked! Thanks