tlightne

You need to put the motions sensor into inclusion mode first. The documentation that came with the sensor will tell you how to do that.. Once it is in inclustion mode remove it from the zwave network first then include it into the zwave network.

@macjeff The plugin in AC shows battery life for two batteries, battery life is main battery and battery life 2 for second battery. I have two doorbells one that is battery only (Back Door) and one is powered (Front Door) with battery backup. Battery Life 2 is 0% because of the obvious only one battery in the doorbell. In the dashboard for the plugin what do the nodes show?

@bmercier Thank you that did the trick... All is well....

Ring Node is not displaying Battery 1 Life % in AC it says TEST. In the PG3X nodes it does show as correct percentage.

You really do not need the Push plugin. The notification plugin and the pushover app on your phone or computer will allow you do do all you need..

I believe the Zwave backup option will only be available if you have the Zmatter dongle.

I use the GE Embrighten 240 volt Zwave switch on my hot water heater to shut off power whenever my water main is closed for what ever reason...

@beninsteon Have been using for 5 years now and have no had any issues... Besides when the link is energized it shuts my water off. So worst case I do a manual over ride..

I am using the same motorized valve that @beninsteon is using with an Insteon I/O link.

@leonpc This is an example of how I do my Christmas under eve LED Lights with the holiday plugin. December Christmas Lights - [ID 00FA][Parent 0133][Not Enabled] If 'Holiday Controller / today Day Node' Month is December And 'Holiday Controller / today Day Node' Day >= 1 And 'Holiday Controller / today Day Node' Day <= 31 Then Run Program 'Blue' (Then Path) Else - No Actions - (To add one, press 'Action')

PG3x is rock solid so did you pull power on Polisy/Eisy after installing? If not pull power wait 20 - 30 seconds then reaply power and wait for reboot. User id and password for PG3x are the same as what you use to login the Polisy/Eisy. I would open a ticket and let UD support check it out.

Nobody is supporting it. Tried to contact author but never got a response awhile back.

It is no different than deleting a device you have to move it from the folder first..

So do you want to proceed or not that is your choice..

My sunset programs ran at the correct sunset time with the UI showing sunset as 1 hour early..

Are you using the 994, Polisy, or Eisy?? To reset Network settings: 994 : Not sure... Polisy : Press and hold the button till the first and second LEDs (from the left) start blinking then release. This action resets all network configuration back to DHCP on the Ethernet jack next to the serial port. All other network interfaces shall be disabled. Eisy : Click the button four (4) times

Plug a lamp into the outlet and go through each device and turn them off. When the lamp turns off that will be the one you were looking for...

I have a few strips of Govee Leds and they are ok. I could not get the govee Node server to work so I removed the Govee controller and use Shelly devices RGBW2 controllers with the Shelly Node server..

Refresh the app after you make any changes with AC.. Also backup UDM after doing the refresh..

My first guess on issue 2 is the SD card is going bad.

Updated my Eisy to 5.7.0_5 PG3x to 3.2.10 today. One reboot when directed to do so and Everything is running as expected....

@4481hoods enter this from a browser. https://eisy.local:8443/WEB/sysconfig.txt

Use the password you use to login to your Eisy admin console..

The Zwave backup option is only available on Polisy/Eisy when you have the Zmatter board from UD.

Are you running the Zmatter board or another Zwave stick? Are your Zwave devices named ZWXXX or ZYXXX?