Techman

The fact that they dropped the price from $79.99 to 49.99 leads me to believe that have added the IOLinc to their discontinued list. It's sad to see the direction that the Company is taking

Click on the link below for instructions. Note that the current version of the firmware does not support the 300 series Zwave dongle. Do you know what version you have?

There lies your problem, your firmware and UI must be the same version. Once you update your UI all your programs should be visible. You should probably update the ISY to the latest version as well

F.Y.I - The IOLinc is no longer available from Smarthome, not sure if it will be restocked at a later date.

What version of the ISY firmware and UI are you running?

Did you try disconnecting the load from the KPL?

When doing a factory reset you have to hold the set button in until the buzzing stops. When the factory reset is completed the KPL load button should light up.

Try disconnecting the load, cap the red wire from the KPL then see if you can install it

Can't Determine Insteon Engine indicates a communication problem between the PLM and the KPL Make sure your firmware and UI are the same version. If not, clear your java cache including all programs and download the ISY launcher Did you do a factory reset on the KPL, i.e. pull out the tab then push the tab back until the KPL beeps and continue holding the tab in until the beeping stops, then do a restore device fron the admin console

I added the Smart Switch 7 yesterday without issues. I'm running 5.3.3

Glad to hear you got it resolved.

Not sure what "Network Empty" refers to. Best to wait for a response from your support ticket.

Click on Zwave, Advanced, Zwave information. Does it show as connected, etc.

It's possible that you may have a bad Zwave back up or that the Zwave dongle is defective. It's best to submit a support ticket to UDI and let them analyze the problem.

Don't try to restore the ISY 4.9.0 firmware as it's not compatible with the 500 series Z-wave dongle. You must do a zwave restore which will populate the 500 series dongle with the data that was stored on your 300 series dongle. Click on Zwave then Zwave version, it should be 6.81.00. If it isn't then the dongle may not be properly installed.

also make sure that your ISY firmware and your UI are the same version. The 500 series is not compatible with the 4.9.0 version so don't do a restore.

Here's the manual on the new USB PLM. Not sure if it will ever see the light of day. It seems that all we would need is a compatible cable. If you scroll down you'll see a 2234-223 which is the serial port version. These are both pending FCC approval. 2234-222.pdf The specs are impressive. 2234-222.pdf

Aeotec shows the Aeotec Siren as compatible, and tested, with the ISY. Try moving the siren to a different location and adding again.

It sounds like it's trying to write updates to your battery operated devices. If that's the case then in the admin console clicik on FILES then disable AUTOMATIC WRITES TO BATTERY POWERED DEVICES. If the battery operated devices show a 1011 to the left of the device name then you'll have to put the device into the linking mode then right click on the device name and then click on write updates. Only one battery operated device should be in the linking mode at any time otherwise your link tables can get corrupted.

We lost internet connectivity for most of the day yesterday and I noticed that I was unable to access the Admin Console over my LAN during the outage. Was it trying to validate credentials over the internet? I thought the ISY / Admin Console were self sufficient.

Adding to the above, only one battery operated device should be in the linking mode at any time. If multiple battery operated devices are put into the linking mode at the same time the link tables can become cross linked. The battery operated device must be manually put into the linking mode before you can write an update to it. Another possibility: the following program worked with earlier ISY firmware versions, not sure if it's currently compatible. Disable or delete the program after you write the updates to the device. If 'South Stairs Motion Sensor' is switched On Then Set 'South Stairs Motion Sensor' Write Changes Else - No Actions - (To add one, press 'Action')

If you delete a device the device will be removed from any program it's associated with. If you factory reset a device then do a restore device the programs won't be affected.

Also take a hard look at the device id 56.18.5A. Make sure it's 18 not 1B as the two can be misread, especially with the newer labeling that Smarthome is using.

Did you follow the "replace PLM procedure" in the attached file? Replace ISY PLM.pdf

I'm not familiar with Home Assistant but it's possible that there may be a conflict between your devices, ISY and Home Assistant. Try putting one of your battery operated devices into the linking mode then do a restore device from the ISY as it's possible that your device link records got corrupted. The restore device should fix that.