Blackbird

Where can I get it and how much is it? Is it software or hardware addon? Thanks

I just bought this remote and see that it can control the hub but don't know about the ISY. I don't have the ISY with IR, is there any way to make this work, maybe by buying an addon device? Thanks

I think you guys have the right answer I will try control instead of status. Thanks

I want to open my bedroom door between 1am and 6am and when it is open the bathroom lights turn on at 1% I currently have a program running but being that the bedroom door is normally open during the day, when 1am hits and the door is still open, the lights come on in the bathroom. Bedroom door open night bathroom light on If Status 'Bedroom Door-Opened' is On And From 1:00:00AM To 6:00:00AM (same day) Then Set 'Bathroom Light' 1% Else - No Actions - (To add one, press 'Action')

Perfect. Thanks Gary

I want to close my bedroom door and have the bedroom lights to ramp down for 21 seconds. I know how to adjust the scene to change the ramp speed when the switch is pressed and I know how the dim feature works in the programs but the dim is too quick. I just want to close my bedroom door (which has a door sensor) and have the lights slowly dim without hitting the light switch

I just checked and yes, for some reason I had a program also controlling the lights. I disabled it and will see if it stops happening. Thanks guys

I have a dimmer switch in the garage named "garage lights inside" and a 8 button keypad in the house named "Garage Lights KP C" . Both control the interior lights of the garage. Sometimes if I turn the garage lights on then off then on again with the dimmer, the lights start to flash and it gets into a never ending loop. The only way to stop it is by disabling the "garage lights inside" dimmer then re enable it. The "Garage Lights KP C" keypad and the "garage lights inside" dimmer are both a controller and responder for the "inside garage lights" scene which the "garage lights inside" dimmer is a part of. Have I messed up something here? usually it works fine but this looping has happened about a dozen times now. Any suggestions? Thanks

Thanks

Can I use a standard 3 way light switch in the basement and a insteon light switch upstairs to control the same lights? Or do both have to be insteon? Thanks

Perfect, Thanks

I just installed 2 more leak detectors and neither one show anything in the current state box Just updated the isy now none of my wireless sensors show any info in the current state box

Thanks for the advice

Please see my other post I mistakenly created a double post. Thanks for the reply

I have the switch at the door wired as n/c but the wire at the i/o link is wired the the n/o. So when door is closed the green light on the i/o link is on. Is that right?

Is there a difference and if so why? A friend does have the aftermarket magnet switch and we wondered which wiring setup to the iolinc is better? Thanks

Is there a difference and if so why? A friend does have the aftermarket magnet switch and we wondered which wiring setup to the iolinc is better? Thanks

Thanks

I haven't used variables yet as I don't understand them. Where would I find a good source of information explaining when and how to use variables in programs? Is there a wiki about it? Thanks

The water shutoff I have only has 3 wires (Red, Green and black) where as the ELK has (Green, Black, Red, White) Any idea about this? I'm guessing green on mine is white on the ELK but I'm not sure

Waterflow is the reason I stay away from pex. Each fitting or elbow inserts inside the tube which is smaller in diameter then the tube which reduces Waterflow. Where as copper is consistent. In my house I have 1/2 inch copper so if I went with 3/4 pex then that would be better. Just my opinion.

Does the water shutoff wire to one of the zones on the ELK?

Was a good deal thanks for mentioning it

I just bought one

how do you connect to the elk? Wire it straight to the panel and no need for the iolinc? Can the insteon water sensor trigger the elk to turn off the water?