G W

No one said forum. When you are on a web page that allows you to make changes, read the entire page. You are going to scare the new kids. Best regards, Gary Funk

That's why everyone says read the manual before operating. Read the entire page then make changes. Best regards, Gary Funk

There are but they cost hundreds to thousands more. Elk is the best ROI I have found. If you can do it yourself it's pretty cheap. It's cost way less that my Insteon system. Best regards, Gary Funk

The nice thing about Insteon is it simplifies the wiring. I have capped off over a dozen red wires. Best regards, Gary Funk

Electricians do funny things at times. I just changed out a three-way switch for an outlet that the white in a 14-3 was wrapped in black tape and used as a load. Best regards, Gary Funk

Set A, B, C and D to Non-Toggle On. Best regards, Gary Funk

Did you set up scenes for each fan? High, Med, Low and off. Best regards, Gary Funk

These all have from the same location. My previous order of 5 also came in 5 boxes. Best regards, Gary Funk

If i had my way, there would no packaging at all. Just put the switches in a small box and ship them. I don't want the instructions, I don't want the wire nuts and I don't want the little white box it comes in. Too damn much waste. Best regards, Gary Funk

I just received 8 new KPL units from Amazon. This is ridiculous. This brings my total to 24 installed KPL. Best regards, Gary Funk

LOL. Best laugh I've had all day. Best regards, Gary Funk

That's the issue I see. I see this like global thermonuclear war. The only way to win is not to play. Best regards, Gary Funk

That's still going to cause some issues with some. The only way I see this working to to be able to give explicit instructions. Guessing what I want is too risky. Best regards, Gary Funk

Do both switches light up in the off position? Did you use the RED wire on both switches? Best regards, Gary Funk

I've had a switch get warm but never hot. Since i switched to LED bulbs my switches don't even get warm. Best regards, Gary Funk

Thank you. Best regards, Gary Funk

Here we go again. MyQ meets all requirements. Let it go. Best regards, Gary Funk

Unless the Echo has 100% voice recognition. I could see arming it or a panic alarm. Best regards, Gary Funk

Exactly. The beam is to be no more than 6 inches above the floor. Best regards, Gary Funk

Mandatory standards are for the electric eyes to activate at 6 inches. DASMA Door and Access Systems Manufacturers Association Look at #7 - the six inch rule From the CPSC Mandatory Standards: https://www.gpo.gov/fdsys/pkg/CFR-2004-title16-vol1/content-detail.html 16 CFR part 1211 TITLE 16--COMMERCIAL PRACTICES CHAPTER II--CONSUMER PRODUCT SAFETY COMMISSION PART 1211--SAFETY STANDARD FOR AUTOMATIC RESIDENTIAL GARAGE DOOR OPERATORS--Table of Contents Subpart A--The Standard Sec. 1211.11 Requirements for photoelectric sensors. (a) Normal operation test. (1) When installed as described in Sec. 1211.10(a) (1)-(4), a photoelectric sensor shall sense an obstruction as described in paragraph (a)(2) of this section that is to be placed on the floor at three points over the width of the door opening, at distances of 1 foot (305 mm) from each end and the midpoint. (2) The obstruction noted in paragraph (a)(1) of this section shall consist of a white vertical surface 6 inches (152 mm) high by 12 inches (305 mm) long. The obstruction is to be centered under the door perpendicular to the plane of the door when in the closed position. See figure 3. Best regards, Gary Funk

That's just wrong. My SUV can be out 1 inch too far and not interfere with the beam. Yet to door will hit the bumper and not close. Best regards, Gary Funk

Why do you say that? I seen that same problem with the safety beam at the correct height. Best regards, Gary Funk

I had the same problem last week. A dead PLM. Best regards, Gary Funk

I use zoho.com and it's really fast. It's free and very easy to set up. Best regards, Gary Funk

You need to identify the "plug" by its device type. Without knowing exactly what this "plug" is, it is difficult to give you the answer. Best regards, Gary Funk