asbril

For those that have me helped along the road and those that have followed my "Zwave struggles".... I have just completed 99 % of the migration from ISY to IoP. There are only a few sensors left and those are easy to transfer. Now I have a lot of programming to do, but that will keep me busy a few days. At first I wanted to wait for the migration tool that, I think, is coming sometime around September, but I have a bug in my ISY that I have not been able to identify and resolve, and I was afraid that a migration tool might bring this bug along. It took me several days, a lot of perspiration, a few curse words here and there, and encouragement from @MrBill, but my approximately 80 Zwave devices as well as a few wifi devices are now all on IoP, and so far so good. About 75 % of the Zwave devices were easy to exclude from ISY and then include in IoP but quite a few needed to be taken out of their switch box and then do the exclusion/inclusion near the ISY and IoP. In some cases I actually brought the ISY near the device, using a Google Nest Wifi pod to connect the ISY to the network. A few devices refused either the exclusion or the inclusion and then I had to simple replace the device with spare ones that I had. There are 2 or 3 devices that work but show some communication errors. I did the "Update Neighbors" with most devices, but I believe that the mesh network will learn the best route over time. Now waiting for Eisy and then definitely I count on Michel to give us a migration tool Thanks again to Michel & Team, as well as to all of you who have given me guidance all this time. I am sure that I will continue to seek your help as needed !

Thanks so much. That seems to have done the job. BTW even though I did the upgrade, in PG3 the message indicating that there is an upgrade is still showing. Hopefully by the time we have the new Zwave board I hope that you (or Firstone) will have time to port AVRemote to PG3 as well.

Many thanks for your suggestion. I am not familiar with MQTT, but I think that your solution is not that different from what I do with Kasa switches which, while not "elegant" does do the job. The new board/dongle is expected by September and Michel mentioned that there is a 90% chance that there will be an easy migration from the 500 board to the new Zwave/Matter board. Then I can migrate everything to IoP.

Nice

@bpwwer If not mistaken you ported Holidays Google to PG3. As mentioned many times, I like this ns very much but have had some issues. Currently I have the PG2 Node server on my ISY, with a number of related programs and I have the PG3 Node server on IoP, currently without any related programs. This morning I notited that in the IoP Administrative Console the Holidays Google nodes show Today May 26 and Tomorrow May 27. Of course today it is June 2. I restarted both the PG3 Node server and Polyglot, but still the same problem. I noticed in the Node server's log an authentication error : 2022-06-02 08:55:06,820 Command udi_interface.interface INFO interface:stop: Disconnecting from MQTT... localhost:1888 2022-06-02 08:55:06,822 Command udi_interface.interface INFO interface:_disconnect: MQTT Graceful disconnection. 2022-06-02 08:55:18,448 MainThread udi_interface INFO polylogger:set_basic_config: set_basic_config: enable=True level=30 2022-06-02 08:55:18,796 MainThread udi_interface INFO __init__:<module>: UDI Python Interface for Polyglot version 3 3.0.46 Starting... 2022-06-02 08:55:18,822 MainThread udi_interface.interface INFO interface:__init__: Initialization received from Polyglot V3 3.0.62 [ISY: 5.4.4, Slot: 25] 2022-06-02 08:55:18,824 MainThread udi_interface.interface INFO interface:__init__: Connect: Network Interface: {'addr': '10.0.0.214', 'netmask': '255.255.255.0', 'broadcast': '10.0.0.255'} 2022-06-02 08:55:18,826 Interface udi_interface.interface INFO interface:_startMqtt: Connecting to MQTT... localhost:1888 2022-06-02 08:55:18,833 MainThread udi_interface.interface WARNING interface:db_getNodeDrivers: controller not found in database. 2022-06-02 08:55:18,835 MainThread udi_interface.custom INFO custom:_save: Sending data customtypedparams to Polyglot. 2022-06-02 08:55:18,835 MainThread udi_interface.interface WARNING interface:send: MQTT Send waiting on connection :: {'set': [{'key': 'customtypedparams', 'value': [{'name': 'calendarName', 'title': 'Calendar Name', 'desc': 'Name of the calendar in Google Calendar', 'isRequired': True, 'isList': True}, {'name': 'token', 'title': 'Google Authentication Token', 'desc': 'Obtain token by visiting authentication URL'}]}]} 2022-06-02 08:55:18,899 MQTT udi_interface.interface INFO interface:_connect: MQTT Connected with result code 0 (Success) 2022-06-02 08:55:18,901 MQTT udi_interface.interface INFO interface:_connect: MQTT Subscribing to topic: udi/pg3/ns/clients/00:0d:b9:52:ce:70_25 - MID: 1 Result: 0 2022-06-02 08:55:18,916 MQTT udi_interface.interface INFO interface:_subscribe: MQTT Subscribed Succesfully for Message ID: 1 - QoS: (0,) 2022-06-02 08:55:19,006 MQTT udi_interface.interface INFO interface:_message: Successfully set controller :: ST to 1 UOM 25 2022-06-02 08:55:21,861 MainThread udi_interface.interface INFO interface:addNode: Adding node Holidays Google Controller(controller) [None] 2022-06-02 08:55:21,863 MainThread udi_interface.interface INFO interface:setController: Using node "controller", driver "ST" for connection status. 2022-06-02 08:55:21,973 MQTT udi_interface.interface INFO interface:_message: Successfully set key = customtypedparams 2022-06-02 08:55:22,443 Thread-1 udi_interface ERROR holidays:parameterHandler: Error getting credentials: (invalid_grant) Bad Request 2022-06-02 08:55:22,740 Thread-3 udi_interface.interface INFO interface:updateProfile: Sending Install Profile command to Polyglot. 2022-06-02 08:55:22,827 Thread-3 udi_interface INFO holidays:start: Started HolidayGoogle Server 2022-06-02 08:55:22,883 MQTT udi_interface.interface INFO interface:_message: custom data response {'customparamsdoc': '<h2>Configuration</h2>\n\n<p>When you start Holidays Google node server for the first time, it will require to authenticate your Google account. Click the link in the notice, copy token, put token into node server configuration parameter and save configuration. You cannot restart node server between clicking the link and saving the parameter.</p>\n\n<p>Holidays Google node server accepts a list of calendars in your account to check for holidays. It will poll holidays changes every long poll (default is 60 seconds). In order for event to be considered as a holiday, it needs to be <em>full day event</em> AND it needs to <em>show time as free</em>.</p>\n\n<p>Two nodes will be created for each configured calendar - today and tomorrow.</p>\n\n<p><strong>DO NOT CHANGE RELATIVE ORDER OF CONFIGURED CALENDAR NAMES.</strong> Doing this will change underlying ISY nodes to the new configuration, potentially requiring you to change ISY programs.</p>\n'} 2022-06-02 08:55:22,922 MQTT udi_interface.interface INFO interface:_message: Successfully set key = customparamsdoc 2022-06-02 08:55:23,041 MQTT udi_interface.interface INFO interface:_message: Successfully set controller :: ST to 1 UOM 25 2022-06-02 08:55:23,217 MQTT udi_interface.interface INFO interface:_message: Profile installation finished Scroll to Top Can you shed any light ? I have similar issues in the past with the PG2, but then it was always just one day off, never 6 days like here.

The way I programmed the Zen32 is that for the 4 bottom buttons, 1 click is ON, 2 clicks is OFF

I am impressed and hope for the 90% probability 500 series backup !

P.S. I don't know if this is necessary, or even useful, but I created a program whereby the no neutral switch is always ON : IF Switch A status is <= 2 % THEN Switch A 3% So, when the switch is OFF, it still has power. With its Led bulbs, thr consumption must be minimum.

I have one switch box in my home where it is practically impossible to get a neutral wire. I tried many solutions including Inovelli but I have fallen out of love with Inovelli. Their no neutral switches gave me problems. A few months ago I installed the "No Neutral" Enbrighten 52252 Z-Wave Plus Smart Light Dimmer and it has worked perfectly since. As you may know Zwave devices really only work well when you have a good mesh network, meaning a minimum number of (non-battery) devices that cover your home. To be safe I usually include my Zwave devices close to my ISY (I built a switchbox with a plug) and then move the switch to its intended location. From time to time I get an error message in the Administrative Console that there is no communication with this switch, but to the best of my memory it has never failed to work.

I have no idea but tomorrow I continue my Zooz stick update exploration. I am using the "old" stick that I had issues with and won't touch the "new" stick, that is currently in the Polisy, until I am fully comfortable that I know what I am doing.

This is as far as I was able to get and need help to reach the sight setup !

I deleted and re-installed the PG3 Holidays Google Node server on IoP, but this time in a different slot..... and now it seems to be working fine.

Michel said that a backup from the Zooz Series 700 dongle can be restored to the new board/dongle, Not sure that a ISY 500 series backup would work (but I hope that it will),

Try restarting Polyglot.

Has anyone succeeded in adding and using the Google Holidays Node server in PG3 ? In my case the nodes appear in the Administrative Console the first time after adding the Node server, but the next time I open the Administrative Console the nodes are empty in the Administrative Console. I wonder whether it is just @StangManD and me having issues with the Holidays Google PG3 version or whether @firstone may need to adjust something.

How exactly did you remove it? In the PG3 Dashboard, enter the Node server and click on Delete. It will (should) delete the Node server both from PG3 and from the Administrative Console. Usually I restart Polyglot and the Administrative Console, but this may not be necessary. how do I install the PG2 version? Go to the Node server Store, Install the Node server. Then go to the (PG2) Dashboard, enter the Node server, Configuration and click on the message asking you to authenticate. I strongly suggest to use "Open link in new tab" (I use Chrome) when clicking on this message. The link will lead you to select the appropriate Google account if you have more than one. You accept the options then given to you, copy the Authetication code, and paste it in the Node server configuration. Either immediately, or after restarting the Node server, the configuration will show your Google calendar(s). Copy each "Configured Calendars" by "Adding Value" in "Calendar Name". Then click on Save, After restarting the Administrative Console the various calendars will show up in the Administrative Console with each 2 nodes "Today" and "Tomorrow". In my Google calendar, I created several sub calendars like "cleaning lady", "trip", which will then be added in the Node server as "Configured Calendars" and show up in the Administrative Console with their respective nodes. This allows me to create programs using (depending on purpose) either the "Tomorrow" or "Today" node of the specific calendar. Remember that this Node server requires that an event is a "All Day" event in the Google calendar, meaning that the Node server will not read an event at a specific time, but of course you can set your desired time in the ISY program that you may create. Let me know if this helpful or if you need more specific guidance.

Excuse my ignorance but what is the meaning/purpose of TPM ? I was able to enable TPM so, based on above comments, I don't need to update the BIOS, but I don't understand what TPM stands for.

As @Bumbershoot writes, this should be the case as long as the 700 device connects directly to the Polisy, without being routed through one or more 300/500 devices.

The best !!!!!

I recommend not to post same issue in different categories of this forum as you may get confusing to follow the responses.

Holidays Google is a great Node server, but in my case it does not work in PG3. While all the necessary nodes show in the PG3 Dashboard, the nodes only "populate" in the Administrative Console once after installation. Then afterwards the niodes remain empty in the Administrative Console. I noticed an authentification issue in the Node server's log. I have removed and installed the PG3 version several times with same outcome. I don't know whether your issue is related, but I have reverted to the PG2 version, hoping that my issue will be resolved in an update.

Thanks for sharing

Fantastic news always from UD ! An easy upgradable Zwave board PLUS Matter !!!!!! I can't wait. @Michel Kohanim Will that future restore also work with ISY (500 Dongle) backup ?

enter "admin" and same for password

If I can do it, then anyone can..... I have no time right now to indicate the steps (I use Putty) but it is not difficult.