Brian H

Although this module is listed as a 220 volt unit. It uses 120 volts for power and is a 30 amp unit. Has both lines and neutral inputs. You can use the Line that powers it and has a switched output for switching your dishwasher. Ignoring the Isolated Line two input and output if you care to. It can be used on 120 volts by not using the second line input and outputs that are on a separate relay. It is also discontinued and the ones still being sold are reconditioned. I have an early production one and it works fine on 120 volts. The users manual is avilable if you care to see if maybe something you could use. http://www.simplehomenet.com/proddetail ... 9357345387 Another way would be an ApplianceLinc switching a heavy duty contactor with a 120 volt AC coil.

To second Lee's information. I have replaced old Hardware V1.3 ApplianceLincs firmware v.28. With V4.1 firmware v.32 and V4.2 firmware v.38 with no problems. The replace module function did it all.

ISY reports my new SynchroLinc as a v.30? My new iMeterSolo reports as a v.87? Didn't do lots of testing with the iMeterSolo but it did add with no hitches. Unlike the Synchrolinc that totally bombed out.

I tried forced i1 and it was added but the Set Options tab blew away on an error. Set back to Automatic and it did show what it was set to but writing changes failed.

Thanks for the fast analysis of the problem. At least we know why it is not 100% functional. Another i2 Quirk. You didn't write the i2 protocol Smartlabs did and you would think they could get it correct. Side note. I am not sure if the SynchroLinc can be both a responder and controller, but when I added it. The side tree for it showed both Is a Controller of and Is a Responder to.

I go the same message when picking it from the drop down list. Auto Discover added it but I got a red! Event Viewer from auto discover: Fri 04/08/2011 06:07:27 PM : ---- Initializing the linked devices ---- Fri 04/08/2011 06:07:27 PM : ---- All Linked Devices are now initialized ---- Fri 04/08/2011 06:07:27 PM : ---- Add remaining devices ---- Fri 04/08/2011 06:07:27 PM : [ 18 F6 4D 1] Removing all links Fri 04/08/2011 06:07:27 PM : [18 F6 4D 1 ] Querying engine version Fri 04/08/2011 06:07:27 PM : [iNST-ACK ] 02 62 18.F6.4D 0F 0D 00 06 (00) Fri 04/08/2011 06:07:28 PM : [iNST-SRX ] 02 50 18.F6.4D 14.82.98 27 0D 01 (01) Fri 04/08/2011 06:07:28 PM : [standard-Direct Ack][18.F6.4D-->ISY/PLM Group=0] Max Hops=3, Hops Left=1 Fri 04/08/2011 06:07:28 PM : [18 F6 4D 1 ] Retrieved engine version is i2 Fri 04/08/2011 06:07:28 PM : [18 F6 4D 1 ] Calibrating engine version ensuring support for i2 Fri 04/08/2011 06:07:28 PM : [iNST-ACK ] 02 62 18.F6.4D 1F 2F 00 00 00 0F FF 01 00 00 00 00 00 00 00 00 00 06 (00) Fri 04/08/2011 06:07:28 PM : [iNST-SRX ] 02 50 18.F6.4D 14.82.98 2B 2F 00 (00) Fri 04/08/2011 06:07:28 PM : [standard-Direct Ack][18.F6.4D-->ISY/PLM Group=0] Max Hops=3, Hops Left=2 Fri 04/08/2011 06:07:29 PM : [iNST-ERX ] 02 51 18 F6 4D 14 82 98 11 2F 00 01 01 00 FF 01 00 00 00 00 00 00 00 00 00 Fri 04/08/2011 06:07:29 PM : [Extended-Direct][18.F6.4D-->ISY/PLM Group=0] Max Hops=1, Hops Left=0 Fri 04/08/2011 06:07:29 PM : [Ext. Msg. Handler] Duplicate response: ignored Fri 04/08/2011 06:07:29 PM : [iNST-ERX ] 02 51 18 F6 4D 14 82 98 1B 88 00 00 00 73 CA 00 00 00 00 00 00 00 00 00 00 Fri 04/08/2011 06:07:29 PM : [Extended-Direct][18.F6.4D-->ISY/PLM Group=0] Max Hops=3, Hops Left=2 Fri 04/08/2011 06:07:38 PM : [iNST-ACK ] 02 62 18.F6.4D 1F 2F 00 00 00 0F FF 01 00 00 00 00 00 00 00 00 00 06 (00) Fri 04/08/2011 06:07:39 PM : [iNST-SRX ] 02 50 18.F6.4D 14.82.98 2B 2F 00 (00) Fri 04/08/2011 06:07:39 PM : [standard-Direct Ack][18.F6.4D-->ISY/PLM Group=0] Max Hops=3, Hops Left=2 Fri 04/08/2011 06:07:39 PM : [iNST-ERX ] 02 51 18 F6 4D 14 82 98 11 2F 00 01 01 00 FF 01 00 00 00 00 00 00 00 00 00 Fri 04/08/2011 06:07:39 PM : [Extended-Direct][18.F6.4D-->ISY/PLM Group=0] Max Hops=1, Hops Left=0 Fri 04/08/2011 06:07:39 PM : [Ext. Msg. Handler] Duplicate response: ignored Fri 04/08/2011 06:07:48 PM : [iNST-ACK ] 02 62 18.F6.4D 1F 2F 00 00 00 0F FF 01 00 00 00 00 00 00 00 00 00 06 (00) Fri 04/08/2011 06:07:49 PM : [iNST-SRX ] 02 50 18.F6.4D 14.82.98 2B 2F 00 (00) Fri 04/08/2011 06:07:49 PM : [standard-Direct Ack][18.F6.4D-->ISY/PLM Group=0] Max Hops=3, Hops Left=2 Fri 04/08/2011 06:07:49 PM : [iNST-ERX ] 02 51 18 F6 4D 14 82 98 11 2F 00 01 01 00 FF 01 00 00 00 00 00 00 00 00 00 Fri 04/08/2011 06:07:49 PM : [Extended-Direct][18.F6.4D-->ISY/PLM Group=0] Max Hops=1, Hops Left=0 Fri 04/08/2011 06:07:49 PM : [Ext. Msg. Handler] Duplicate response: ignored Fri 04/08/2011 06:07:53 PM : [18 F6 4D 1 ] i2 data transfer commands do not work. Reverting to i1 Fri 04/08/2011 06:07:53 PM : [18 F6 4D 1 ] Using engine version i1 Fri 04/08/2011 06:07:53 PM : [iNST-ACK ] 02 62 18.F6.4D 0F 28 0F 06 SET-MSB(0F) Fri 04/08/2011 06:07:53 PM : [iNST-SRX ] 02 50 18.F6.4D 14.82.98 2B 28 0F SET-MSB(0F) Fri 04/08/2011 06:07:53 PM : [standard-Direct Ack][18.F6.4D-->ISY/PLM Group=0] Max Hops=3, Hops Left=2 Fri 04/08/2011 06:07:53 PM : [iNST-ACK ] 02 62 18.F6.4D 0F 2B F8 06 PEEK (F8) Fri 04/08/2011 06:07:54 PM : [iNST-SRX ] 02 50 18.F6.4D 14.82.98 2B 2B 00 PEEK (00) Fri 04/08/2011 06:07:54 PM : [standard-Direct Ack][18.F6.4D-->ISY/PLM Group=0] Max Hops=3, Hops Left=2 Fri 04/08/2011 06:07:54 PM : [ 18 F6 4D 1] Adding device to ISY Fri 04/08/2011 06:07:54 PM : [iNST-ACK ] 02 62 18.F6.4D 0F 10 00 06 ID-REQ (00) Fri 04/08/2011 06:07:54 PM : [iNST-ERX ] 02 51 18 F6 4D 14 82 98 1B 88 00 00 00 79 9C 00 00 00 00 00 00 00 00 00 00 Fri 04/08/2011 06:07:54 PM : [Extended-Direct][18.F6.4D-->ISY/PLM Group=0] Max Hops=3, Hops Left=2 Fri 04/08/2011 06:07:55 PM : [iNST-SRX ] 02 50 18.F6.4D 14.82.98 2B 10 00 ID-REQ (00) Fri 04/08/2011 06:07:55 PM : [standard-Direct Ack][18.F6.4D-->ISY/PLM Group=0] Max Hops=3, Hops Left=2 Fri 04/08/2011 06:07:55 PM : [iNST-SRX ] 02 50 18.F6.4D 07.09.30 8B 01 00 (00) Fri 04/08/2011 06:07:55 PM : [standard-Broadcast][18.F6.4D-->07.09.30] Max Hops=3, Hops Left=2 Fri 04/08/2011 06:07:55 PM : [synchrolinc] Start : Adding device to ISY Fri 04/08/2011 06:07:55 PM : [synchrolinc] Finish : Adding device to ISY was Successful Fri 04/08/2011 06:07:55 PM : [18 F6 4D 1 ] Link 0 : 0FF8 [E201148298FF1F01] Saving [E201148298FF1F01] Fri 04/08/2011 06:07:56 PM : [iNST-ACK ] 02 62 18.F6.4D 0F 19 00 06 LTSREQ (LIGHT) Fri 04/08/2011 06:07:56 PM : [iNST-ERX ] 02 51 18 F6 4D 14 82 98 1B 88 00 00 00 7A 01 00 00 00 00 00 00 00 00 00 00 Fri 04/08/2011 06:07:56 PM : [Extended-Direct][18.F6.4D-->ISY/PLM Group=0] Max Hops=3, Hops Left=2 Fri 04/08/2011 06:07:56 PM : [iNST-SRX ] 02 50 18.F6.4D 14.82.98 2B 00 00 (00) Fri 04/08/2011 06:07:56 PM : [standard-Direct Ack][18.F6.4D-->ISY/PLM Group=0] Max Hops=3, Hops Left=2 Fri 04/08/2011 06:07:56 PM : [ 18 F6 4D 1] ST 0 Fri 04/08/2011 06:07:57 PM : [iNST-ERX ] 02 51 18 F6 4D 14 82 98 1B 88 00 00 00 7A 65 00 00 00 00 00 00 00 00 00 00 Fri 04/08/2011 06:07:57 PM : [Extended-Direct][18.F6.4D-->ISY/PLM Group=0] Max Hops=3, Hops Left=2 Fri 04/08/2011 06:07:58 PM : [ 18 F6 4D 1] Device added to ISY Fri 04/08/2011 06:07:59 PM : ---- All Remaining Device Added ---- Fri 04/08/2011 06:07:59 PM : [iNST-ACK ] 02 62 18.F6.4D 0F 19 00 06 LTSREQ (LIGHT) Fri 04/08/2011 06:08:00 PM : [iNST-SRX ] 02 50 18.F6.4D 14.82.98 2B 00 00 (00) Fri 04/08/2011 06:08:00 PM : [standard-Direct Ack][18.F6.4D-->ISY/PLM Group=0] Max Hops=3, Hops Left=2 Fri 04/08/2011 06:08:00 PM : [ 18 F6 4D 1] ST 0 Fri 04/08/2011 06:08:00 PM : [All ] Writing 8 bytes to devices Fri 04/08/2011 06:08:00 PM : [18 F6 4D 1 ] Using engine version i2 for 'Synchrolinc' Fri 04/08/2011 06:08:00 PM : [18 F6 4D 1 ] Link 0 : 0FF8 [E201148298FF1F01] Writing [E201148298FF1F01] Fri 04/08/2011 06:08:00 PM : [iNST-ACK ] 02 62 18.F6.4D 1F 2F 00 00 00 0F FF 01 00 00 00 00 00 00 00 00 00 06 (00) Fri 04/08/2011 06:08:00 PM : [iNST-SRX ] 02 50 18.F6.4D 14.82.98 2B 2F 00 (00) Fri 04/08/2011 06:08:00 PM : [standard-Direct Ack][18.F6.4D-->ISY/PLM Group=0] Max Hops=3, Hops Left=2 Fri 04/08/2011 06:08:01 PM : [iNST-ERX ] 02 51 18 F6 4D 14 82 98 11 2F 00 01 01 00 FF 01 00 00 00 00 00 00 00 00 00 Fri 04/08/2011 06:08:01 PM : [Extended-Direct][18.F6.4D-->ISY/PLM Group=0] Max Hops=1, Hops Left=0 Fri 04/08/2011 06:08:01 PM : [Ext. Msg. Handler] Duplicate response: ignored Fri 04/08/2011 06:08:01 PM : [iNST-ERX ] 02 51 18 F6 4D 14 82 98 1B 88 00 00 00 7B 46 00 00 00 00 00 00 00 00 00 00 Fri 04/08/2011 06:08:01 PM : [Extended-Direct][18.F6.4D-->ISY/PLM Group=0] Max Hops=3, Hops Left=2 Fri 04/08/2011 06:08:10 PM : [iNST-ACK ] 02 62 18.F6.4D 1F 2F 00 00 00 0F FF 01 00 00 00 00 00 00 00 00 00 06 (00) Fri 04/08/2011 06:08:11 PM : [iNST-SRX ] 02 50 18.F6.4D 14.82.98 2B 2F 00 (00) Fri 04/08/2011 06:08:11 PM : [standard-Direct Ack][18.F6.4D-->ISY/PLM Group=0] Max Hops=3, Hops Left=2 Fri 04/08/2011 06:08:11 PM : [iNST-ERX ] 02 51 18 F6 4D 14 82 98 11 2F 00 01 01 00 FF 01 00 00 00 00 00 00 00 00 00 Fri 04/08/2011 06:08:11 PM : [Extended-Direct][18.F6.4D-->ISY/PLM Group=0] Max Hops=1, Hops Left=0 Fri 04/08/2011 06:08:11 PM : [Ext. Msg. Handler] Duplicate response: ignored Fri 04/08/2011 06:08:20 PM : [iNST-ACK ] 02 62 18.F6.4D 1F 2F 00 00 00 0F FF 01 00 00 00 00 00 00 00 00 00 06 (00) Fri 04/08/2011 06:08:20 PM : [iNST-SRX ] 02 50 18.F6.4D 14.82.98 2B 2F 00 (00) Fri 04/08/2011 06:08:20 PM : [standard-Direct Ack][18.F6.4D-->ISY/PLM Group=0] Max Hops=3, Hops Left=2 Fri 04/08/2011 06:08:21 PM : [iNST-ERX ] 02 51 18 F6 4D 14 82 98 11 2F 00 01 01 00 FF 01 00 00 00 00 00 00 00 00 00 Fri 04/08/2011 06:08:21 PM : [Extended-Direct][18.F6.4D-->ISY/PLM Group=0] Max Hops=1, Hops Left=0 Fri 04/08/2011 06:08:21 PM : [Ext. Msg. Handler] Duplicate response: ignored Fri 04/08/2011 06:08:25 PM : [18 F6 4D 1 ] Link 0 : 0FF8 [E201148298FF1F01] *Failed Writing [E201148298FF1F01]

Yes I am ruining 3.1.2. I tried both auto discover and picking it from the drop down list, but I was not aware of the four minute power up self calibration thing. I may have tried one of the choices after the four minute thing or started before the thirty second pause before going into the self calibration thing. Supposed to double beep when self calibration starts. I can't remember if you are a member of the Developers Group. If you are there is a SynchroLinc Developers Notes pdf file avilable for download.

I just got a SynchroLinc today. The full users manual indicates it automatically goes into a self calibration mode after power on. That times out after four minutes. It also seem to indicate that adding it to things like HL2 should not be started until it was in the calibration mode? I also got some errors when trying to add it to my ISY setup. Maybe UDI has some tips for us as I don't know if we should try it while it is in power up self calibrate mode or wait until it times out. http://www.smarthome.com/manuals/2423A5.pdf

Unfortunately. Each fan manufacturer seems to control speed differently. Making a Insteon fan controller that can do all fans would be a challenge. Yours look like Fantech varies the voltage to it with a control that can take the fans load. Other manufacturers may switch capacitors or motor leads to vary the speed.

There are no Insteon devices that can control a fans speed. There is a whole thread on this subject in the Smarthome forums. http://www.smarthome.com/forum/topic.asp?TOPIC_ID=7992

Installed fine this morning.

It is also against code to use a dimmer switch in a J-box to control an outlet. Same reason. Too easy to blow something up. Dimmer switch in a J-box controlling hard wired fixtures. OK.

2412S has been discontinued for a fairly long time now. I believe Simplehomenet makes an equivalent to the 2412S. I have seen no feedback on how it works with an ISY99i.

Installed fine for me. Only thing I noticed was the module status was blank until I closed the program and restarted it.

Are the CFLs dimmable? If not; they should not be used with a dimmer type switch. Many times even if they are dimmable. They can make power line interference that can effect things. The best thing is relay type modules and switches for CFLs.

Michel; Did the 2477D dual band Switchlinc ever have v.35 firmware in it?

Smarthome sells a nine volt adapter and on the sales page. It says can be used with the 2420M.

Sometimes you get hits from the search function. Some terms I think may find something have no hits others more than I really wanted.

Error message numbers are found here. http://www.universal-devices.com/mwiki/ ... r_Messages I am sure UDI will give you the scoop on if they are a big problem.

The unit communicates with the automation controllers by an RS232 connection. I don't believe the Serial Port on the ISY99i could be used to interface to the unit.

9 volts should be fine. I asked about the voltage range in this thread. http://forum.universal-devices.com/viewtopic.php?t=3593 On the bottom of the 2413S sales page. They do show an optional ISY Power Supply, but it is not very obvious.

Look at the CT-800 sensor used in this tutorial. http://www.cocoontech.com/portal/articl ... ?showall=1 You could pass one of the two 220 volt power wires for the pump through the CT-800 and trigger an I/OLinc's sensor input.

The RemoteLinc is in the Device Type List. 00.05 I have used the Auto Discover and it was added. Just have to remember to turn the linking mode on or it isn't found. Firmware v.33. V1.0 RemoteLinc. I have seen a V1.2 reported as having a v.35 firmware. Michel gave me a reason why I should not go that route in an earlier post to this thread. But it was added. I don't have any newer revisions. So new ones may not act the same as mine.

Unless something has changed. You can't. Though on my old revision RemoteLinc. I can manually link modules to the All Buttons and not have any of the six paddles in the loop. The Diagnostics Show Device Links Table. For the RemoteLinc. Does show the extra links to the All Buttons and flags an extra link message in the compare functions.

I really doubt it. What make and model? The RCS TX15 and TXB16 come to mind.