Brian H

viewtopic.php?f=25&t=9612

Well it is listed in the drop down list. In 3.3.3.

Page 9 of the RemoteLinc 2 manual shows how to set it to non toggle 8 button. Always sends an On and not an alternate of an On then an Off. Older Remotelinc doesn't have any non toggle modes that I can see.

Well I am not a good one with programming. That said. It does look like you are sending multiple signals in a rapid fashion. You maybe flooding the power lines with signals. Depending on which ones got through different lights may or may not change as commanded.

I tried an original v.24 2476D and after making the changes through My Lighting. Cycling the power by pulling the Air Gap Switch and waiting for maybe 15 seconds. Then gently pushing the switch back to its Normal position. The new settings took. Only thing to watch is if you push the Air gap Switch all the way in. A factory reset is done.

I can say 32 bit Java 7 is working OK for me. V7, Update 7, build 1.7.0_07-b10

Since almost all X10 devices are receive only and Insteon modules are two way. Sometimes the more Insteon devices you add the less reliable the X10 devices are and more reliable the Insteon gets. Reason is the transmitter circuit loads the signal down somewhat and Insteon modules only resend Insteon messages to each other. It could be possible that the X10 commands properly. I have never seen a new 2413S have the problem but do have an older 2412S that flaked out on X10.

Do you have the ELK M1 EXP Interface with your M1? It is mentioned in the ELK configuration in the wiki. http://www.universal-devices.com/mwiki/ ... figuration You may also find more help in the ELK section here if you have not looked yet. viewforum.php?f=17

Iris seems to be a unconventional system. There are some Zigbee devices in the mix. From what I have seen on their support pages.

As a battery powered device. The Motion Sensor goes into a power saving mode and will not respond to a query. The status display in the administrative pane is the last known state. If I have a Switchlinc showing On and I use an X10 command to turn it Off. The consoles still shows On as it didn't process the X10 Off.

If you try the Air Gap power cycle. When you push it in. Only go to its normal position. If you push it all the way in you can factory reset it.

Do you have the Pro Version or the Standard Version? There is a chart at the bottom of the ISY99i Sales Page with some information. http://sales.universal-devices.com/residential/isy-99i/

Glad to read you have it working.

Satwar, Read LeeG's earlier response. The USB RF PLM should be supported by the later SHN Utilities. I believe it will show up as a serial type device as its drivers make it look like a serial port.

That kit is an I/OLinc and a water sensor that changes state when a certain amount of water is in the sensor. You should be able to use the I/OLinc's sensor input state through the ISY interface to trigger or inhibit watering. If you want to read about the sensor in the kit and some of the users feedback. http://www.smarthome.com/3107RS/Claber- ... ers/p.aspx I don't know how sophisticated the EZFlora's water sensor works. Could just inhibit the EZFlora valves or actually send date to the ISY for processing.

Do we know if the new 2413 PLM base EZFlora even supports the options jack anymore? Since the old 2412 PLMs had a power transformer in them and the 2413 based PLMs have a high efficiency power line derived one. Maybe external connections to 5 volts and common signal ground are no longer there.

It is shown on the second page of the command set document. http://www.simplehomenet.com/Downloads/ ... %20Set.pdf Since they now have no pass through outlet. It may not be a feature anymore. I have no personal information on it. It looks like when the sensor has rain in it. It stops the zones from going On when commanded.

The later EZFlora units have a auxiliary input connector for a Rain Sensor and a Single Pulse Per Revolution water meter. Not sure if it would be of use in your case. Maybe someone with an EZFlora can elaborate on the inputs uses. If yours don't have the connector. Maybe things have changed again.

I am not too surprised on the changes. The Insteon Engineers frequently do changes and sometimes the documentation department is not in the loop so to speak. I have also found if you have real old modules. Frequently their documentation just vanishes completely and if you didn't have a hard copy. OH well.

One way X10 devices without a power line transmitter in them. Just ignore a Status Request to their X10 address and no response is sent or should be expected by the sender of the request. The PR511 has a power line transmitter in it as it can be set to send X10 commands to additional X10 addresses. I don't have information on if it responds to a Status Request, but it sounds like it might from IndyMikes findings.

Does the original X10 setup turn them On and off or also dim the lights and change the fans speeds? The Levitons are powered by AC and you may want to look at a KeypadLinc. Then an OutletLinc for your X10 controlled outlet and an InlineLinc {relay or Dimmer} for the fixture module.

Maybe fifteen minutes ago. I got the ISY994i file. Just now the link for the ISY994i also goes to the sales pages. Now both are broken.

Most of the present X10 devices are power line receive only and ignore a Status Request. The RR501 and a few of the old discontinued two way modules. LM14A, AM14A do respond to a Status Request and use X10 Extended messages that are not recognized by the PLM. The two way Smarthome X10 modules will also respond to a Status Request.

The ISY99i download link does go to the sales page. The ISY994i link does get you a download file.

Are you running the latest 3.2.6 firmware on your ISY99i? New switches are now I2CS and need 3.2.6 to be used properly.