Techman

The sensors send a heartbeat signal every 24 hours, so 25 hours is a safe bet. That's what I use.

The only way to test the insteon leak sensor is from the sensor itself. You can put a wet paper towel under the sensor to trigger it. You'll then need to remove the towel and press the set button to clear the "wet on " node. Some of the leak sensors had different firmware and may not need the button press to clear the wet node.

@CPrince Are you using the UD Zmatter board, or a 3rd party Zwave controller (which may not be fully supported)? Are both your Polisy firmware and UI on 5.8.4

What zwave board (300 or 500) do you have in your ISY994, and is that the one you want to back up? Is Zwave currently functional in your ISY? Your ISY Zwave version should display, try removing power from the ISY for a minute then power it up.

Have you tried doing a factory reset on the Aeotec device?

In your Customizations tab, set it for text. If that doesn't resolve your issue then set it for HTML and place <BR> at the end of your sentence.

Are you on an eisy or polisy. What is your firmware and UI version? A few things you can try: exclude the device from you controller, charge the battery, and then bring the device close ot your controller and include it.

To upate the Polisy firmware, press the multifunction button once. See below: Multi Function Button There's a little multi function button behind the very small hole on the front of the unit. This button has multiple purposes outlined below. Every click on the button will cause the unit to beep. If the button does not behave as described below, please update Polisy. Update and Upgrade All the Packages Click the button once. Please consult support before updating this route. See link below for suggested update/upgrade process.

Yes you need to take it down and bring it next to your admin console. When you press the set button 1 time it will wake up the sensor for 10 seconds, then you need to quickly write the new config parameters while the sensor is awake.

To reduce its range you have to set the MS senistivity (parameter 1) to a lower number, somewhere between 1 and 5. The default setting is 6. In the configuration setting insert 1 for the parameter number, and a value between 1 and 5 for the Parameter Value. and 1 Byte, then click on set configuration. The Sensor must be in the linking mode before you press Set Configuration.

@technoroom The PLM only supports Insteon and has no relationship with Zwave.

@DJonas Glad to hear you got your issue resolved. How do you like the ZSE70, I was thinking of picking a few up to replace some of my Insteon MS. Are there any issues with the MS beta firmware?

There's no option to roll back the firmware. You can try removng power for a minute, then boot up.

Others are also having issues with the latest update, 5.8.4_1. It's best to wait for a bug fix.

There's an issue with 5.8.4_1. It's best to open a support ticket

There appears to be an issue with 5.8.4_1. You should open a support ticket

It might be a Java issue. Try clearing your Java cache, be sure to check all 3 boxes, then download the current IoX Launcher from here: https://isy.universal-devices.com/start.jnlp Nor sure where the 5.8.4_1 came from unless it was just released on the day you updated. My system is current and only shows 5.8.4 Are you on Windows or Mac? PG3x 3.2.27 is the current version.

I think UDX was updated to 3.6.2.7. Not sure what the prior version was. You can check your current version using this link (assuming your on an eisy). Let me know if you have a different version. eisy.local:8443/WEB/sysconfig.txt

@Bill Morrow Post a copy of your ISY error log

The EISY is the HUB. The Zmatter board which is part of the HUB supports the Zwave mesh network As I mentioned earlier, the ZSE70 is currently using beta firmware, so it's possible that it may not be fully functional until the final firmware is released. The Zooz products and the Zmatter board along with the EISY are all quality products. You can try bringing the ZSE70 closer to the EISY, if it then works you'll need to add a repeater to extend its range.

I corrected the link, try again. Zwave is a mesh network, just as Insteon is. The zwave signal, in a zwave mesh network, gets repeated by other non-battery Zwave devices Zwave LR does not use the Zwave mesh network. The device communicates directly with the hub. When you install a zwave LR capable device it should give you the option of either installing it as LR or as part of the Zwave mesh network Depending on how far your ZSE70 is located from the eisy, and how may walls the signal have to go through, would determine if you need a repeater. Any plug in Zwave device acts as a repeater. The ZAC38 would be a good choice, I have one in my network.

Yes, the Zmatter board is Zwave LR certified, but I don't think the current eisy firmware supports LR. If it did then when you add a Zwave LR device it should give you the option of adding it as either LR or as part of the Zwave mesh network. Take a look at this article: https://www.thesmartesthouse.com/blogs/the-smartest-blog/all-about-z-wave-long-range

The ZSE70 is currently running beta firmware. You should occasionally check their support site for the final firmware update which has not yet been released. The LR is not yet supported on the eisy so it's possible that you may need a Zwave repeater between the eisy and the ZSE70 I've had good results with the EISY and Zooz product compatibilty.

@BobM99 You should use the USB PLM, the instructions for switching PLMs are in the migration info I sent you.

The complete migration instructions can be found at this link: https://wiki.universal-devices.com/Eisy:User_Guide#Migration Be sure to follow the migration guide exactly.