Techman

For my lights, I use several scenes, each with different on levels, and call them up with a program. I've not tried your method, so not sure if it's viable. Under scene on levels, the only variable options I have are dates.

Can you post a copy of your program Is your variable state or integer?

Yes, assuming that the bulb is connected to an Insteon module or a Zwave module. The Polisy cannot control a load directly.

Feit has dimmable vintage bulbs. Here's the link Vintage Light Bulbs for Antique Style Lighting - Feit Electric

The Zmatter board is due to be released on 11/15. A version with more memory and storage may be forth coming after the initial release, but that could change. You can pre-order it here: ZMatter: Z-Wave+ & Matter Module for Polisy (Beta) – Universal Devices (universal-devices.com)

When I run UPDATE PACKAGES, the Polisy appears to be updating, but if I again run the update packages the Polisy again appears to be updating no matter how many times I run the update. PG3 did successfully update to 3.1.12

@BobM99 Many thanks

The ISY doesn't always recognize all the Zwave nodes from a device. What series Zwave dongle do you have? I wouldn't worry about the other nodes. What's the make and model of your smoke detractor as Iwas thinking of moving over to Zwave detectors.

Current firmware is 5.4.4 On the configuration tab there are two update options, BIOS and UPDATE PACKAGES. if the update bios is not greyed out then you first need to update the bios then the packages

Are you using the Insteon Smoke Bridge? The only nodes that really matter are SMOKE DETECTED, CO2 ALARM and LOW BATTERY. I have the Insteon smoke bridge (2982-222), and my nodes are a little different than what you've posted, but basically the same. I'm not sure that the ISY would respond to the nodes other than the ones I've mentioned.

Amazon Prime is showing October 28th as a delivery date for a 12 volt 2-amp power supply. The only other source I can think of is All Electronics in Van Nuys. http://www.allelectronics.com They might do an overnight ship. You might also send an email to UD to see if they will ship overnight. I believe they also ship out of Van Nuys. You can also check the Best Buy store in your area Note: UD recommends a 12v, 2 amp supply.

What City are you located in? Do you have access to Amazon Prime?

The IOLincs are single band, powerline only, devices and are not as reliable as dual bank devices. The fact that you have pending writes to the devices means that they are not reliably communicating with the PLM. It's also possible that the garage door opener is creating noise on the powerline that's interfering with the Insteon signal. Take a look at this troubleshooting link. You won't have a reliable system until you resolve the communication issue. https://wiki.universal-devices.com/index.php?title=INSTEON:_Troubleshooting_Communications_Errors I had to put a powerline filter on my garage door opener in order to get my IOLinc to work properly.

Your screenshot show that you have writes pending. Right click on the device and then click on "Write updates" If the KPLs still don't update, then try a factory reset/restore device on the new KPL. It's also possible that the PLM is not able to communicate with the KPL. Let me know what happens after you try the above

The UD store website still shows shipping November 15th.

In order for the dongle to work you need to activate the module via UD If their link isn't working, then send them a support ticket at: support@universal-devices.com

Also try removing power from the isy, wait about 15 seconds, then power up

@Steve L Are your variables state variables? If not change them to State.

It's remotely possible that the SD card is damaged. Also check your ethernet cable and try rebooting your router. Are you trying to access the ISY from the admin console?

@JSchumann I'm using the same email settings as you, however I don't have TLS checked and I'm using a different ISP, not Comcast You might try increasing the timeout, and/or unchecking TLS

I'm running 5.3.4 and use text messages via ATT.NET and found it to be very reliable with no delays. I have my timeout(ms) set to 6000

@larryllix Could you post a screenshot of your "search" option. Are you referring to "find/replace"?

Update your ISY firmware an UI to 5.3.4, it has bug fixes that may help. The update is easy.

You can try both I have several Multisensor 6 and found them to be very reliable. On one occasion I had to remove and re-add one to the Zwave network to clear up an anomaly. When you re-add the sensor it may report in Celsius for a short while before it automatically changes to Fahrenheit. What ISY firmware and UI are you running? What Zwave board do you have, the 300 or 500 series?

What's the make and model of your sensor? You can try uninstalling and re-installing the sensor, that may clear up the anomaly.