Techman

Actually adding a new Insteon device via the admin console is quite simple. Click on "Link Management", "New Insteon Device", then enter the device's address xx.xx.xx and then click OK. It's always best to have your ISY updated to the latest firmware to ensure compatibility with the device you're adding.

I didn't look at the link tables after adding it, but it appeared to work as it should. I have since removed it and put it back in storage so I'm unable to run any more tests.

@Chris Jahn "Install Dev. Packages" tab, how and when would it be used?

@DennisC Here are the ISY to EISY migration instructions from the UDI Wiki Eisy:User Guide - Universal Devices, Inc. Wiki (universal-devices.com)

Under the Z-wave menu click on BACKUP. The instructions probably need to be updated, they may be from the 300 series dongle.

@Illusion Just pulled my spare SynchroLinc out of storage. I was able to link to the ISY994, running 5.3.4 firmware, without a problem. 2423A5 V1.15 Date code: 1129 Have you tried adding a dual band plug in module in the same socket as your SynchroLinc. That would help in the event you have noise on your power line. If you have Z-wave, the Aeotec Smartswitch 7 is a good replacement option for the SynchrLinc.

You need to first update your ISY to the latest firmware, 5.3.4. Once you restore the backup up on the eisy power cycle the eisy. Prior to restoring the backup on your eisy you need to verify all your programs and scenes as the update from 4.9.0 to 5.3.4 requires some user intervention. Be sure to first read the firmware release notes.

F.Y.I. Every time Java does an update it deletes the memory parameter, which then needs to be reentered.

Run a diagnostic / compare link tables. It's possible that either the ISY or the Device has corrupted links. Another possibility is that being the appliancelinc is a single band device you could have some power line noise issues.

I'll try to get to my box of "stuff" in the next few days. With the one I have installed I had to add a dual band plug in module close to it in order for it to work. If you have an extra plug-in module laying around, you might try plugging it into the same socket at the Synchrolinc you're trying to install.

What gets installed if you click on the "Install Dev. Packages" button in the System tab?

Current firmware for Polisy is 5.5.4 Try removing power from the Polisy, then clear your java cache, including installed applications, then download the IoX Launcher.

@NFLnut My Multisensor 6 is showing Fahrenheit with eisy running 5.5.4. Try removing power from the MS6. After it powers up it could take a while before it changes from Centigrade to Fahrenheit, so give it a couple of hours. All my Multisensor 6 which I have on the ISY994 started out reporting in Centigrade then after a couple of hours changed to Fahrenheit. It's possible that it needs location information from the Hub.

Try clearing your Java cache, including installed applications, then download the IoX Launcher Do you see the Polisy in the IoX Launcher

The Polisy supports the following PLMs: 2412S and 2413S through the DB9 connector on the back. 2413U and 2448A7 through the USB port on the back

My eisy updated to 3.1.20 without issues. My Polisy is at 3.1.16 and won't update. I tried removing power, and did an Iox reboot, but it still won't update.

Take a look at the Polisy user guide, it contains the migration instructions: Polisy:User Guide - Universal Devices, Inc. Wiki (universal-devices.com)

Try the refresh button in the Launcher. Also try powering down the eisy for a minute. Is your eisy on Wi-Fi or ethernet?

Your firmware versions are correct for migration. Do you have Z-wave or are you just migrating Insteon?

All your issues have been previously reported to UD. Hang in there, the next firmware update should resolve them.

This is a documented issue UD is aware of it and it will hopefully be fixed in the next eisy / Polisy firmware release.

@SteveT As far as the Zmatter board not detecting some device status changes, this is a documented bug and should be resolved in the next firmware release.

The Polisy with the Zmatter card is a controller. A z-wave device can only be linked to one controller. What is it that you would like to accomplish?

You also might want to contact the developer of the node server.

Are you using an ISY994 or ? What's your firmware and UI version