Techman

Wi-Fi is disabled when the ethernet cable is plugged in and connected to your router. If Wi-fi has been previously setup, then when you disconnect the ethernet cable it will automatically revert back to wi-fi.

Is it possible to create a run widget for an "if" or "then" clause in a program?

I was able to update both the Polisy o 3.1.17 and PG3x on the eisy, however it took a few attempts before successfully updating.

Can you connect to the ISY using the IoX Launcher, if so, verify the Firmware and UI versions. Be sure to first delete your java cache including installed applications, then download the IoX Launcher

I've had the same problem with eisy and had to add it manually to the launcher. However, the eisy will occasionally disappear from the launcher and needs to be manually added back again. I also have a Polisy and ISY994 that are in the launcher that continue to be displayed without issues. Anyone else have their eisy disappear from the launcher after adding it?

@Javi I finally got it working. The esiy wifi was connecting to my guest network which blocked it from my main network, which is why it didn't show up. The wired connection was properly connecting to my main network. Javi, thank you for all your help. It's much appreciated.

I pressed the search icon, but it didn't find anything, and I'm back to square one. My eisy is using a reserved address in the router, and I had renamed it when I set up the address. My Polisy and ISY994 connect to the LAN from UD Mobile without any errors, the problem is only with the eisy on Wi-Fi

Try adding it manually to the IoX Launcher, that's what I had to do.

Is your router Wi-Fi 6 , Is you connection on 2.4 or 5ghz Do you get any error messages in UD Mobile when you're connected via Wi-Fi. Are you connecting via a LAN or the Portal

@Javi The setup was done from Settings > Wi-Fi Configuration. I don't see Wi-Fi Credentials. I have remote Connection Settings access disabled, and Local Connection Settings enabled. The local port is set at 8080. The system was not connected to the Portal. I reset the network on the eisy and then retried a Wi-Fi configuration. It showed that the Wi-Fi credentials were uploaded to the eisy, but when I try to access the eisy from UD Mobile on the LAN I get an error "Unexpected close, Host unreachable" When I test the local connection for the eisy from UD Mobile, I get "ERROR (IOException) java.net.ConnectException:Failed to connect to /192.168.1.200:8080" I can see the eisy on the LAN when I use a wired connection, but not on Wi-Fi. I'm only using the home network. eisy firmware is 5.5.2

All the devices should included in the scene as Controllers.

I'm trying run my eisy on Wi-Fi, on the LAN with limited success. Ethernet connection works without issues via UD Mobile and the IoX launcher. In the eisy Wi-Fi setup, it connects to the System Access Point, and sets the WiFi credentials, but I get an unexpected token error when I try to synchronize. I also show a "System error Unexpected Close. Host unreachable" on the main page. I'm able to see my programs, devices, etc. Anyone have their eisy on a LAN with a Wi-Fi connection? If so, what ports are you using?

In the configuration tab, click on Upgrade Packages

@Illusion I was looking at your device link table for the 1.15 SynchroLinc and noticed that one has 3 lines of links. Mine only has 2 lines, the last line being all 0. I think that there's some data still embedded in your device(s) that didn't clear when you reset it. I would try several factory resets. I've attached the user manual in case you don't have one 2423A5 SynchroLinc Manual.pdf

Yellow is Zwave Red is Zigbee/Matter

These are the Multisensor 6 nodes than now show up with the 5.5.2 firmware and Zmatter The humidity node which should be in the "Multisensor" node is now displayed in the "Weather Sensor" node

The one I have installed was done many years ago with an older ISY firmware. I do have a spare, but it's buried in a box and hard to get to. If you're still having issues I could try to dig out in a day or two. The SynchroLinc is a single band device, so you might try putting it closer to the PLM when you attempt to link it. Be sure to do a factory reset on it first. If you have Zwave, the Aeotec SmartSwitch 7 will accomplish the same and more as the SynchroLinc.

I have a SynchrolLinc, Hardware 1.15, firmware v.30 that's on my ISY994 running firmware 5.3.4 with no issues.

My error, I thought it was a 2477D that was connected to the bulbs. As Jackman suggested, the quality of the bulbs is most likely the problem. The 2477S switches the load with a relay.

The driver circuit in your LED bulbs may not be compatible with triac dimmers which Insteon uses. The A15 is not a widely used bulb, you may want to contact their customer service regarding compatibility Philips and Feit bulbs work well with Insteon but I'm not sure if they have a A15 base

The 2412S PLM is an older single band device with a limited link database. Its RS232 interface is outdated and may not support some of the newer devices. It was replaced by the 2413S. It's possible that it's not compatible with the Polisy and eisy.

@GTench Humidity is there, it's showing up in a separate node called weather sensor, not in the window where it should be. After doing a Synchronize, I still have UV displayed in the main window

@Chris Jahn With IoX 5.5.2: Detect Button Press now correctly defaults to OFF The Multisensor 6 does not correctly update the motion status node, and the temperature is still reporting in Centigrade rather than Fahrenheit

IoX 5.5.2 is now available. Click on update packages to install it. After the update you'll need to clear your Java cache and download the IoX Launcher

"Cannot determine Insteon Engine" means that the PLM is unable to communicate with the device The discontinued ApplianceLinc is a powerline only device. Either you have interference on the powerline or the two legs of your powerline are not bridged. Adding a dual band device close to the ApplianceLinc may help. All LampLincs are dimmable, do you mean an on/off module?