Techman

@walkman9999 Your ISY firmware is outdated. You should consider moving up top 5.3.4 which has bug fixes and newer hardware support. The upgrade will require some user intervention so be sure to read the release notes before updating.

The USB PLMs should be available Q1 2023. You can add your name to the notify email list at the link below USB Modem Interface (PLM) – Insteon

Here's the link Serial PLM Kit - Universal Devices (universal-devices.com)

Use port 587 for SMTP

@bjs The IF is used to evaluate a condition. Being that your IF statement is blank nothing will happen when you call it. The THEN statement will run when either it's called from another program or if it meets the conditions in the IF statement.

A few things to try/check In your Sunset program you need to run the DOWSTAIRS "THEN" not the "IF" Make sure your variables are STATE and not integer variables if they trigger a function. I see where you're setting the variables but not where they are in the program Sometimes adding a 2 second WAIT before a line that's not executing helps.

The newer on/off switches have only 2 leds, on and off. They install and work just like the previous release. On/off switches are not, and cannot, be used as dimmers as they use a relay and not a triac, to control the load.

170001 are informational messages and can be ignored.

If you have an unused/spare zwave device, try installing it In the Zwave menu, under advanced, zwave information, you should see the info in the attached screenshot, assuming that you don't have the Zooz dongle attached.

Try removing power from the Polisy for about 15 seconds. The Polisy should see the new board, If it's still not recognized then It's probably best to open a support ticket with UD support@universal-devices.com

If the red led blinks when you push a KPL button it means that one of the responders didn't acknowledge the message. If it flashes green that means that the responder(s) acknowledged the message If it's just a faint red while the KPL is idle I would just ignore it and move on.

Yes, but the migration option isn't available yet, hopefully sometime this week. For now, I'm using the Polisy as a test platform, and using the 994i to run everything

Make sure "Zwave support" box is checked on the configuration tab. Zwave should be working using the current firmware.

The 2334-222 is in stock Dimmer Keypad, 8-Button – Insteon Did you try doing a factory reset by pulling out the set button, then pushing in the set button, and holding it in until the KPL beeps, continuing holding it in until the beeping stops. The load should then turn on. Then do a restore device from the admin console.

When you hear back from UD could you post the steps taken to resolve the issue for others who may have the same problem

It's probably best to open a support ticket with UD. support@universal-devices.com

@inovermyhead Try removing power from the Polisy for about 15 seconds then allow it to reboot If it's not on 5.4.5 then try another package update

Try pressing the reset button on the front of the Polisy ONCE which should update you to 5.4.5 After the update clear your Java cache, including all applications and then download the ISY launcher

Probably a wise decision.

If I do a restore device I get the attached error message.

Yes

I had a similar problem. I did a synchronize nodes which fixed it.

They're in the email sent by UD

Just finished installing the Zmatter board. When installing the antenna connectors on the Polisy case place the serrated washer on the inside and the split locknut on the outside under the nut. Once the nut is tightened down the antennas won't move. You might have to rotate the antenna connectors when inserting them into the Polisy lid, they definitely fit without doing any modifications to the lid Connecting the antenna leads to the Zmatter board once the board is installed is somewhat difficult, as the Zigbee lead barely makes it to the board. It's probably best to connect the antennas to the board before inserting the board. I started fresh and removed my Zwave devices and the Zooz dongle before the installation. After the installation I installed a few test Zwave devices without out issues. For now, you just get the basic Zwave options. Looking forward to future firmware updates with the enhanced Zwave features.

Insteon is alive and well. Some products are currently available, others will be available in Q1 2023. Here's the link to the new Insteon store: Collections – Insteon