Techman

@stillwater It's asking for your portal user name and password If you want to use your previous name and password add the following URL line in IoX Launcher: https://eisy.local:8443/desc then click save

@Michel Kohanim I just saw your previous post, so I guess I'm ok

@Michel Kohanim Where do you see an additionnal partition My Eisy is as I received it out of the box. I never modified it. The partition must have been added before it was shipped. Can the partition be deleted, if so how?

@Geddy My memory usage stills shows 23% PG3 took a long time to come back up, longer than usual, after the reboot, but I still had to restart my node servers @Michel Kohanim My disk partitions are untouched and original, same as @Geddy

UPDATE I rebooted the eisy and now memory usage is showing 23% However, upon reboot all my node servers seemed to hang up. I had to do a restart on them. After the restart the audio player was showing volume at 40% when in fact it was at max.

Not exactly sure what you're referring to. Do you mean the boot enviroment Where do you see partitions?

With one boot enviroment the memory usage is stilll showing high

You need to clear your java cache, be sure to check all 3 boxes, then download the IoX Launcher from here: https://isy.universal-devices.com/start.jnlp

Does 6.1.1 fully support Zwave LR Update went smoothly, no problems Re : Where to buy the Zooz Zwave dongle, add https://www.thesmartesthouse.com Their price is lower than Amazon

I have no idea, I took a look at my programs after updating to 6.1.1 and they were all OK

Can a Zwave backup of the UD Matter dongle be restored to the Zooz 800LR dongle if I'm only using Zwave or do I have to rebuild the Zwave network?

You really don't need the query all program, but if you want it, in the THEN statement add SET EISY QUERY

It's possible that the Zse11 is defective, Zooz tech support is very responsive. Send them an email

It's posible that when you switched to batteries it cleared the status in the battery window. Give it a couple of days to see it it populates the battery level.

Thanks, I sent an email to Somfy to ask what's going on with the unavailability of their controllers

Where did you get your Tahoma, the Somfy website shows every controller as out of stock. I'm currently using the ZRTSI which was discontined a long time ago.

The ZSE11 batteries may need replacing or you may have a marginal connection between the device and your controller Have you updated the device to the lastest firmware, 2.3.0, which was released 7/2026

What's your eisy firmware version What Zwave controller are you using? Have you tried doing a factory reset on the switch, then a zwave switch exclude and include on the eisy

I've seen cases where one defective Insteon device can wreak havoc on the entire insteon network. A power failure/voltage spike can damage a device Create a program with the then clause "Set EISY Query". When you run it this will show you the devices the eisy can't communicate with. Disable those devices, by pulling out the set button or unplugging it, a few at a time. This will help you eliminate those devices as a problem

It's possible that power cycling your controller close to midnight is affecting the schedule. Try setting the power cycle at 12:30 am. You can also try changing the last two lines in the configuration

Did you remove power from the EISY before replacing the PLM. You may want to try a restore/replace PLM again (see attached). Even if the old PLM was missing links, the EISY would have written the correct links to the new PLM Replace PLM Procedure (EISY or POLISY).pdf

What controller and its firmware are you using Try removing power from your plm and your controller, then power up the PLM, wait 15 seconds, then power up your controller Let me know if that resolved your issue

If your're using Bluetooth make sure the output of the Audio Player is set to Bluetooth and not Speaker Jack

Write updates writes the link tables stored in the ISY to the device. The devices with the 1011 in the left margin means there is a mismatch between the device and the ISY.

Make sure you're changing the parameters from the primary node